EasyManua.ls Logo

Clarke SE16C150 - User Manual

Clarke SE16C150
16 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OPERATION & MAINTENANCE
INSTRUCTIONS
LS1216
Original Instructions
AIR COMPRESSOR
ELECTRIC MOTOR DRIVEN

Other manuals for Clarke SE16C150

Questions and Answers

  • L
    Larry HoganAug 20, 2025
    Why Clarke Air Compressor will not start automatically?
    • T
      Todd PenningtonAug 20, 2025
      There are several reasons why your Clarke Air Compressor might not start automatically: * A blown fuse: Check the fuse rating and replace it if necessary. * A tripped starter overload: Reset it by depressing the button. * A defective pressure switch: Have an electrician change the pressure switch. * Fault in electrical installation: Let an electrician check electrical installation.
  • E
    Edward HuntAug 22, 2025
    Why does my Clarke SE16C150 Air Compressor run continuously and can’t attain the working pressure required?
    • T
      Tammy MaysAug 22, 2025
      If your Clarke Air Compressor runs continuously without reaching the required working pressure, consider the following: * Blocked suction filter: Change the filter. * Slack V-belt: Tighten the V-belt. * Leak between compressor block and air receiver: Tighten the connection and repair the leak. * Suction rendered difficult or impossible at suction intake or the air being taken in is too warm: Ensure unobstructed airflow around the unit.
  • A
    Antonio NixonAug 25, 2025
    What to do if Clarke SE16C150 Air Compressor unit starts and stops more frequently than usual?
    • S
      Scott WalkerAug 25, 2025
      If your Clarke Air Compressor starts and stops more frequently than usual, it could be due to: * Large amount of condensation in the air receiver: Drain off condensation at least once a week. * Leaks in the control unit or inspection cover: Locate leaks and repair them.
  • P
    Paula SimmonsAug 26, 2025
    Why does my Clarke SE16C150 Air Compressor unit start, but stop again after only a few revolutions?
    • L
      Leon SheaAug 26, 2025
      If your Clarke Air Compressor unit starts but stops after only a few revolutions, consider these causes: * Leaking non-return valve: Disconnect from the mains supply and empty air receiver. Clean or replace the non-return valve. * Blocked non-return valve: Thaw the non-return valve out. Ensure the unit is installed in a frost-free place.
  • J
    Jessica FloresAug 28, 2025
    What to do if Clarke SE16C150 becomes too hot?
    • P
      Paula JohnsonAug 28, 2025
      If your Clarke air compressor becomes too hot, it could be due to: * Insufficient ventilation: Ensure sufficient air is supplied to the flywheel or fan and that hot air is properly vented. * Low oil level: Fill with oil. * Dirt on cooling fins or the suction filter: Clean the cooling fins and suction filter.
  • Z
    zmillerAug 29, 2025
    Why Clarke SE16C150 Air Compressor’s oil consumption rising?
    • A
      Andrew DonovanAug 30, 2025
      If your Clarke Air Compressor's oil consumption is rising, consider these potential causes: * Too much oil in the compressor: Check the oil level a few minutes after stopping. * Working temperature of compressor too high because of insufficient cooling: Increase ventilation to air compressor. * Intake air filter blocked: Clean or change the air filter. * Unit too small in proportion to air consumption: Connect supplementary. * Semi-automatic unit Load too small: Convert to fully automatic operation.
  • E
    Elizabeth GrayAug 31, 2025
    Why is there oil in the air delivered by my Clarke SE16C150?
    • T
      Taylor Pham DDSSep 1, 2025
      If there is oil in the air delivered by your Clarke Air Compressor, it could be due to: * Sump over full: Reduce oil to the correct level. * Intake air filter blocked: Change the air filter.
  • S
    shannon69Sep 2, 2025
    What to do if Clarke Air Compressor unit starts when no air is being used?
    • S
      Stacey BurnettSep 2, 2025
      If your Clarke Air Compressor unit starts when no air is being used, it is likely due to leaks in the pipework system. Locate and repair any leaks.
  • P
    Phyllis AlvarezSep 4, 2025
    How to fix unusual noise from Clarke Air Compressor?
    • R
      Robert PerezSep 4, 2025
      If you notice an unusual noise from your Clarke Air Compressor, check the following: * Loose bolts: Tighten the bolts. * V-Belt flywheel or cooling coil touching belt guard: Find the place of contact and remedy the fault. * Loose flywheel: Tighten the flywheel. * Unit installed on an unsuitable base: Move the unit to a more solid base.
  • K
    Katelyn GardnerSep 6, 2025
    What to do if Clarke SE16C150 Air Compressor keep blowing fuses?
    • G
      Gary KochSep 6, 2025
      If your Clarke Air Compressor keeps blowing fuses, it might be due to an inadequate size fuse installed. Replace it with the correct fuse, referring to the chart.

Summary

Introduction

Data Table

Table listing specifications for various CLARKE air compressor models.

Guarantee

Environmental Recycling Policy

Noise Levels

Residual Risk

Safety Precautions

Installation

Electrical Connections

Lubrication

General Arrangement

Outlet Pressure Adjustments

Portable Compressors

Instructions for adjusting outlet pressure on portable compressor models.

Stationary Compressors

Notes that stationary models do not have adjustable outlet pressure.

Overload Button (Single Phase Only)

Details how to reset the motor overload protector on single-phase models.

Troubleshooting Chart

Torque Values for Cylinder Head Bolts

Maintenance Chart

Declaration of Conformity

Clarke SE16C150 Specifications

General IconGeneral
BrandClarke
ModelSE16C150
CategoryAir Compressor
LanguageEnglish

Related product manuals