Clarke XE36/C200 User Manual

Clarke XE36/C200

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

OPERATION & MAINTENANCE

INSTRUCTIONS

DL0822 - ISS 6

ORIGINAL INSTRUCTIONS

AIR COMPRESSOR

XE RANGE - ELECTRIC MOTOR DRIVEN

Table of Contents

Questions and Answers:

J
Joann SchroederSep 2, 2025
Why is the oil consumption rising in my Clarke Air Compressor?
- A
  Angela AguilarSep 2, 2025
  If your Clarke Air Compressor's oil consumption is rising, check the oil level 2 or 3 minutes after stopping the compressor, as there may be too much oil in compressor. Ensure there is adequate ventilation to the air compressor to avoid high working temperatures. If the intake air filter is blocked, clean or change it. If your semi-automatic unit load is too small, convert to fully automatic operation. If the unit is too small in proportion to air consumption, connect supplementary.
Y
youngjosephAug 23, 2025
Why won't my Clarke XE36/C200 start automatically?
- W
  William FordAug 25, 2025
  If your Clarke Air Compressor won't start automatically, several issues could be the cause. It could be an electrical installation fault, which should be checked by an electrician. The starter overload may have tripped; try resetting it by depressing the button. A blown fuse could also be the reason; check the fuse rating and replace it if necessary. Finally, a defective pressure switch may be the culprit, in which case you should have it changed by an electrician.
T
Theodore LoweryAug 31, 2025
Why Clarke XE36/C200 unit starts and stops more frequently than usual?
- V
  Virginia GarciaSep 1, 2025
  If your Clarke Air Compressor starts and stops more frequently than usual, it might be due to a large amount of condensation in the air receiver (drain it at least once a week) or leaks in the control unit or inspection cover (locate and repair leaks using soapy water).
K
Kara MoranAug 31, 2025
Why is my Clarke XE36/C200 becoming too hot?
- C
  Courtney SimpsonAug 31, 2025
  If your Clarke Air Compressor is overheating, it could be due to insufficient ventilation. Ensure adequate airflow to the flywheel or fan and proper venting of hot air. Other causes include a low oil level (check and fill as needed), dirt on cooling fins or the suction filter (clean them), or a partly blocked non-return valve (clean or thaw it out). If the compressor is being overworked, consider using a larger unit.
L
lisa13Aug 30, 2025
What to do if my Clarke Air Compressor runs continuously and can’t attain the working pressure required?
- E
  ericbrownAug 30, 2025
  If your Clarke Air Compressor runs continuously without reaching the required pressure, consider these possible causes: a blocked suction filter (change the filter), a V-belt that is too slack (tighten the V-belt), or a leak between the compressor block and air receiver (tighten the connection and repair the leak). Also, ensure unobstructed airflow around the unit.
J
Jacob WalkerAug 29, 2025
Why Clarke Air Compressor will not start automatically?
- H
  hulljohnnyAug 29, 2025
  Several factors can prevent your Clarke Air Compressor from starting automatically. It could be due to a fault in the electrical installation, which should be checked by an electrician. Other potential causes include a current supply failure, voltage drop, a faulty motor starter, incorrect motor connections, or a tripped starter overload, which can be reset by depressing the button. Also, check for a defective pressure switch (have it changed by an electrician) or a blown fuse (check the fuse rating and replace if necessary).
D
David BrooksAug 28, 2025
What to do if my Clarke Air Compressor will not start automatically?
- G
  Gabriel MontesAug 28, 2025
  If your Clarke Air Compressor will not start automatically, here are some things to check: * Reset the starter overload by depressing the button if it has tripped. * Check the fuse rating and replace it if blown. * Let an electrician check electrical installation.
M
Michael BrownAug 27, 2025
Why does my Clarke Air Compressor become too hot?
- J
  Jessica StephensAug 28, 2025
  If your Clarke Air Compressor becomes too hot, take the following steps: * Ensure sufficient air is supplied to the flywheel or fan and that hot air is properly vented. * If the oil level is too low, fill it with oil. * Clean any dirt from the cooling fins or suction filter. * Clean or thaw out non-return valve.
F
Frank ChaneyAug 27, 2025
What to do if my Clarke XE36/C200 Air Compressor runs continuously and can't reach working pressure?
- A
  armstrongmatthewAug 27, 2025
  If your Clarke Air Compressor runs continuously and cannot reach the required working pressure, check the following: * Change the suction filter if it's blocked. * Tighten the V-belt if it's too slack (not applicable to direct drive machines). * Tighten any loose connections and repair any leaks between the compressor block and air receiver or near the air receiver. * Ensure unobstructed airflow around the unit if the suction intake is difficult or the air being taken in is too warm. * If the suction filter is blocked, you should change it.
M
Mrs. Maria DayAug 26, 2025
What to do if Clarke Air Compressor starts, but stops again after only a few revolutions?
- X
  xgreenAug 27, 2025
  If your Clarke Air Compressor unit starts but stops after only a few revolutions, disconnect it from the mains supply and empty the air receiver. The non-return valve may be leaking, so clean or replace it. If the non-return valve is blocked, possibly frozen, thaw it out, ensuring the unit is installed in a frost-free place.

Clarke XE36/C200 Specifications

General

Brand	Clarke
Model	XE36/C200
Category	Air Compressor
Language	English

Related product manuals

Preview: Clarke XE10/100

Clarke XE10/100

Preview: Clarke XE Series

Clarke XE Series

Preview: Clarke JUMBO

Preview: Clarke HUNTER

Preview: Clarke BANDIT

Clarke SE18C200

Clarke SE11C100

Clarke Hunter 54

Clarke SEV11C100

Preview: Clarke SHHHAIR 30/9

Clarke SHHHAIR 30/9

Preview: Clarke AIR PIONEER 100

Clarke AIR PIONEER 100