Why do both the wash tank temperature and the final rinse temperature not display on my CMA Dishmachines CMA-180UC?
If neither the wash tank temperature nor the final rinse temperature displays on your CMA Dishmachines Dishwasher, the thermometer transformer is likely defective. You should replace the thermometer transformer with part number P/N: 03202.60.
Why does the motor run when the door is open on my CMA Dishmachines CMA-180UC?
If the motor of your CMA Dishmachines Dishwasher runs with the door open, it could be due to a defective reed switch, which requires replacement with part number P/N: 00557.55. Alternatively, a defective pump motor contactor, which requires replacement with part number P/N: 15504.00, could also be the cause.
What to do if the heater never turns off in my CMA Dishmachines CMA-180UC?
If the heater in your CMA Dishmachines Dishwasher never turns off, it could be due to a defective thermostat, which requires replacement with part number P/N: 13417.89. Another possible cause is a defective heater contactor, which requires replacement with part number P/N: 15504.50.
What to do if the power light does not light but the machine runs on my CMA Dishmachines Dishwasher?
If the power light does not light but the machine runs on your CMA Dishmachines Dishwasher, the power light is likely defective. Replace the power light (red) with P/N: 00406.00.
Why is my CMA Dishmachines Dishwasher motor inoperative?
The motor of your CMA Dishmachines Dishwasher might not be working because the door is open. Ensure the door is closed properly. Other potential causes include: * The control panel is pulled out: Secure the control panel. * A defective reed switch: Replace it with P/N: 00557.55. * A defective timer assembly: Replace it with P/N: 14408.80. * A defective pump motor contactor: Replace it with P/N: 15504.00. * A defective motor: Replace it with P/N: 00201.66.
Why is the rinse water flow low in my CMA Dishmachines Dishwasher?
Low rinse water flow in your CMA Dishmachines Dishwasher might be due to low rinse water pressure. See “Low rinse water pressure” in PROBLEM column. It could also be caused by limed up rinse arm spray nozzles; try de-liming the rinse arm nozzles.
Why does the rinse water run with the door open on my CMA Dishmachines CMA-180UC?
If the rinse water runs when the door is open on your CMA Dishmachines Dishwasher, the reed switch is likely defective (P/N: 00557.55) and needs to be replaced.
Why does the start switch on my CMA Dishmachines CMA-180UC require more than 1 second to activate the cycle?
If the start switch on your CMA Dishmachines Dishwasher requires more than 1 second of activation to start the cycle, the (Instant Start) ice cube relay is likely defective (P/N: 00631.00) and needs to be replaced.
Why does my CMA Dishmachines Dishwasher wash tank or final rinse display the wrong temperature?
If your CMA Dishmachines Dishwasher's wash tank or final rinse displays the wrong temperature, it could be due to a defective digital thermometer. Replace the digital thermometer with P/N: 03202.45. Another possible cause is a defective thermister; replace the thermister with P/N: 03202.65.
Why does my CMA Dishmachines CMA-180UC motor run with the door open?
If the motor in your CMA Dishmachines Dishwasher runs when the door is open, it could be due to a defective reed switch (P/N: 00557.55) or a defective pump motor contactor (P/N: 15504.00). Both of these parts would need to be replaced.
Details on the required electrical supply, circuit, and wiring for the CMA-180UC dishwasher.
Information on water supply connection, pressure, flow rate, and drain connection requirements.
Procedure for filling the booster tank and connecting the high limit switch for initial operation.
A checklist for installers to ensure all installation requirements are met before operation.
Instructions on how to operate and clean the CMA-180UC dishmachine daily.
Detailed troubleshooting steps for various operational problems, including likely causes and solutions.
General| Type | Undercounter |
|---|---|
| Dimensions | 23.75" W x 25.5" D x 33.5" H |
| Capacity | 30 racks per hour |
| Water Consumption | 1.5 gallons per cycle |
| Power | 3.5 kW |
| Weight | 130 lbs |
| Booster Heater | Optional |
| Electrical | 60Hz |
| Wash Cycle Time | 120 seconds |
| Door Type | Front |
| Voltage | 208/240V |
To Next Page