Warranty
This warranty only applies in the United States of America.
Emission control system warranty
Atlas Copco Construction Tools AB warrants to the initial purchaser of the machine and each subsequent owner
that the engine in the machine (in Atlas Copco-brand breaker/drill models Cobra Pro, Cobra TT, Cobra Combi
and in Chicago Pneumatic-brand breaker model CP Red Hawk, as applicable) meets the following two conditions:
(1) the engine, including all parts of its emission control system, is designed, built, and equipped so it conforms
at the time of sale to the initial purchaser with the applicable requirements in 40 CFR Part 1054 regulated by
the U.S. Environmental Protection Agency; and (2) the engine, including all parts of its emission control system,
is free from defects in materials and workmanship that may keep it from meeting the applicable requirements
in 40 CFR Part 1054 regulated by the U.S. Environmental Protection Agency. (The above-stated warranty is
referred to herein as “this Emission Control System Warranty”.) This Emission Control System Warranty covers
all components whose failure would increase the engine’s emissions of any pollutant regulated by the United
States Environmental Protection Agency under 40 CFR Part 1054.
The warranty period for this Emission Control System Warranty begins on the date of sale of the machine to
the initial purchaser and ends two years thereafter.
Where a warrantable condition exists under this Emission Control System Warranty, warranty repairs will be
made by an Atlas Copco Representative (as defined below) or by a service facility designated by the Atlas
Copco Representative, without charge for diagnosis, parts, or labor, subject to all other provisions stated herein.
All defective parts replaced under this Emission Control System Warranty become the property of the Atlas
Copco Representative. Normal maintenance items are warranted up to their first required replacement interval
only. Only Atlas Copco Construction Tools AB approved replacement parts may be used in the performance
of any warranty repairs under this Emission Control System Warranty and will be provided without charge.
This Emission Control System Warranty does not extend to components or parts which are affected or damaged
by the machine owner’s or any other person’s (other than Atlas Copco Construction Tools AB’s or the Atlas
Copco Representative’s) improper use or improper maintenance (including, but not limited to, improper
replacement of filters, sparkplugs or other maintenance items or wear parts; incorrect oil or fuel; stale or improper
fuel mix; dirt or other contaminants in the fuel or oil; excessive dirt, dust, rust, or corrosion in the engine; improper
storage; use of replacement parts or accessories not conforming to the original specifications which impair the
effectiveness of the emission control system; incorporation of or use of unsuitable attachments or unauthorized
alteration of any part; or improper repair), abuse, accident, or acts of God.
This Emission Control System Warranty does not cover replacement of expendable maintenance items (for
example spark plugs and filters) unless they are original items defective in material or workmanship and the
first required replacement interval (in accordance with applicable instructions published by the machine
manufacturer) for the item has not been reached.
Responsibility for Maintenance:
As the machine engine owner, you are responsible for the performance, at your expense, of the proper
maintenance of the engine (in addition to all other parts of the machine and accessories) in accordance with
applicable instructions published by the machine manufacturer, including in the Safety and Operating Instructions
manual for the machine. Atlas Copco Construction Tools AB recommends that you retain all receipts and
maintenance records covering performance of maintenance. Proper maintenance includes, but is not limited
to, routine replacement and servicing of spark plugs, filters, other expendable wear parts, and any other part
or item related to emission control or that may affect emissions.
Requirements related to warranty claims:
Warranty repairs may only be performed by an Atlas Copco Representative or by a service facility designated
by the Atlas Copco Representative to perform the warranty repair. “Atlas Copco Representative” means the
dealer in the United States from whom your machine was initially purchased as a new machine or a service
facility in the United States that is owned or operated by Atlas Copco Construction Equipment LLC and which
performs warranty repair of such machine engines. You are responsible for promptly presenting the machine
(into which the engine is incorporated) to the nearest Atlas Copco Representative as soon as a warrantable
condition exists under this Emission Control System Warranty. At the time of requesting warranty repair, you
must provide proof of the initial purchase of the machine, including the initial purchase date.
© 2010 Atlas Copco Construction Tools AB | No. 9800 0995 93 | 2010-01-12
Original instructions
26
COBRA PRO, TT, TT-AWDSafety and operating instructions
To Next Page
Loading...
Need help?
General