COMAC Innova Comfort - User Manual

Questions and Answers

J
Jennifer LewisAug 15, 2025
How to troubleshoot a COMAC Scrubber that does not start?
- R
  Rebekah WeaverAug 15, 2025
  If your COMAC Scrubber machine won't start, first ensure the main switch is set to "I". If there's an alarm message on the display, stop the machine immediately and contact a specialized service center. Also, check that the batteries are correctly connected to each other and to the machine's electrical system by rotating the recovery tank to its maintenance position. Lastly, a low battery charge level can prevent starting, so run a complete charge cycle.
R
Robert JamesAug 18, 2025
Why is the COMAC Scrubber squeegee not drying perfectly?
- A
  Alexandra KrauseAug 18, 2025
  If the COMAC Scrubber squeegee isn't drying perfectly, check for obstructions in the squeegee itself. Ensure the vacuum tube is also free of any blockages. Additionally, verify that the filter-float of the recovery tank is clear. Finally, make sure the cap on the recovery tank drainage tube and the recovery tank lid are correctly positioned.
J
Jason Saunders MDAug 21, 2025
What to do if COMAC Scrubber batteries are not charged correctly?
- C
  Connor PittmanAug 21, 2025
  If your COMAC Scrubber batteries aren't charging correctly, verify that the battery charger cable is properly inserted into the battery connector and that the plug on the battery charger's power cable is correctly inserted into the electrical outlet. Also, ensure that the characteristics of the mains power supply match those required by the battery charger. If the LEDs of the battery charger blink repeatedly, consult the battery charger's manual to understand the meaning of the flashing signals during the battery recharge stage.
J
Jimmy PatrickAug 25, 2025
Why is my COMAC Scrubber not vacuuming correctly?
- B
  Brianna DanielsAug 26, 2025
  If your COMAC Scrubber machine does not vacuum correctly, first, check if the recovery tank is full and empty it if necessary. If the tank isn't full, the vacuum device might be obstructed.
J
Joel HughesAug 28, 2025
What causes a COMAC Innova Comfort to not clean correctly?
- S
  Samantha JonesAug 28, 2025
  If the COMAC Scrubber isn't cleaning correctly, it could be due to several reasons. The machine might not be starting, or not enough detergent solution might be coming out. Check that the brushes are correctly inserted and that the type of brush used is suitable for the dirt being cleaned. Also, check the state of wear of the brush, replacing it if necessary.
C
crawfordaaronAug 31, 2025
Why is there insufficient detergent solution on the brushes of my COMAC Scrubber?
- C
  Christopher RussellSep 1, 2025
  If you have insufficient detergent solution on the brushes of your COMAC Scrubber, it could be that the quantity of detergent solution in the water system is not sufficient for the work to be carried out, so check that the amount of detergent solution present in the machine's water system is sufficient. Another potential cause is a clogged detergent solution filter, so check the detergent solution filter is not obstructed and clean it if necessary.
S
Shannon ReevesSep 4, 2025
What causes a COMAC Innova Comfort Scrubber to have very low work autonomy?
- C
  Cynthia SmithSep 4, 2025
  If your COMAC Scrubber machine has a very low work autonomy and the battery charge level is critical, perform a complete charge cycle.
D
Duane BrownSep 7, 2025
What to do if a COMAC Innova Comfort does not move?
- C
  clarencemcdonaldSep 7, 2025
  If your COMAC Scrubber machine does not move, the machine might not be starting. Another possible reason is an issue with the drive pedal. If this is the case, stop the machine immediately, and contact a specialized service center.
S
Sara KochSep 12, 2025
Why is my COMAC Innova Comfort Scrubber producing excessive foam?
- A
  Austin JenningsSep 12, 2025
  Excessive foam production in your COMAC Scrubber can occur if the detergent being used is not suitable. Ensure you're using a low foam detergent and, if needed, add a small amount of anti-foam liquid to the recovery tank. If the floor isn't very dirty, try diluting the detergent more.