EasyManua.ls Logo

COMAC SIMPLA 50 B - User Manual

COMAC SIMPLA 50 B
31 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
USE AND MAINTENANCE MANUAL
SIMPLA 50 B-BT
SIMPLA 50 E
ED. 10-2010 EN
ORIGINAL
INSTRUCTIONS
Doc. 10026263
Ver. AA

Table of Contents

Questions and Answers

  • C
    Calvin ElliottAug 2, 2025
    Why is the COMAC SIMPLA 50 B squeegee not drying perfectly?
    • S
      Susan McgeeAug 2, 2025
      If the COMAC Scrubber's squeegee isn't drying properly, several factors could be at play. First, ensure the squeegee rubbers are clean. Then, verify that the suction tube is correctly inserted into its housing on the recovery tank. Also, check that the inner filter of the recovery tank isn't dirty; clean it thoroughly if needed. Finally, consider adjusting the inclination and height of the squeegee.
  • J
    James VelasquezAug 8, 2025
    How to fix insufficient water on the brush of COMAC Scrubber?
    • M
      Martha BrownAug 8, 2025
      If there's insufficient water on the brush of your COMAC Scrubber, start by checking that the solution filter isn't blocked. Next, ensure the tap beneath the symbol is turned on. Finally, confirm that there's water in the solution tank.
  • C
    Christopher HillAug 14, 2025
    What to do if COMAC SIMPLA 50 B does not clean well?
    • M
      Mr. Raymond WrightAug 14, 2025
      If your COMAC Scrubber isn't cleaning well, check the condition of the brush for wear and tear; replace it if the bristles are about 15 mm long. You might also consider using a specialized brush designed for particularly resistant dirt, available upon request.
  • R
    Rebecca RiddleAug 20, 2025
    Why is COMAC SIMPLA 50 B Scrubber producing excessive foam?
    • W
      williamellisAug 20, 2025
      If your COMAC Scrubber is producing excessive foam, first verify that you're using a low-foam detergent. If the issue persists, try adding a small amount of antifoam liquid to the recovery tank. Remember that when the floor isn't very dirty, more foam can be generated, so the detergent solution should be more diluted in such cases.
  • W
    williamhillAug 26, 2025
    What to do if electric fuses and thermal cut-outs are triggered in COMAC Scrubber?
    • G
      George ArnoldAug 26, 2025
      In the event of malfunctioning with the COMAC Scrubber, check if a thermal cut-out has intervened. If the motor overheats, its thermal cut-out will block the electricity supply. Wait a few minutes for it to cool down, then press the specific circuit breaker button to reactivate the power supply and motor operation.

Summary

Introduction and Safety Information

Introduction to the Comac Machine

Overview of the floor scrubbing machine's function and intended use.

General Safety Regulations

Critical safety guidelines to prevent operator harm and machine damage.

Machine Preparation and Setup

Handling and Unpacking the Machine

Instructions for safely handling, unpacking, and moving the packaged unit.

Battery Fitting and Connection

Steps for connecting batteries, including safety precautions for B-BT models.

Squeegee Assembly and Adjustments

Procedure for assembling the squeegee and adjusting its height and inclination.

Solution Tank Setup

Guide for filling and preparing the solution tank for systems without CDS.

Operating the Machine

Preparing the Machine for Work

Steps to prepare the machine for operation, including power and initial checks.

Overflow Device Function

Explanation of the overflow device in the recovery tank and its function.

End of Work Procedures

Procedures at the End of Work

Steps to follow after work, including cleaning, parking, and safety measures.

Daily Maintenance

Cleaning the Recovery Tank

Step-by-step guide to clean the machine's recovery tank.

Cleaning the Suction Filter

Instructions for removing and cleaning the suction filter assembly.

Brush Disassembly and Cleaning

How to remove and clean the machine's brushes for optimal performance.

Weekly Maintenance

Replacing Squeegee Rubbers

Guide on replacing worn squeegee rubbers for optimal drying results.

Cleaning the Solution Tank

Steps to clean the machine's solution tank and filter.

Troubleshooting Common Issues

Machine Not Cleaning Effectively

Diagnosing and resolving issues where the machine fails to clean floors properly.

Squeegee Drying Performance Issues

Troubleshooting steps for when the squeegee leaves floors wet.

Electrical Protection Systems

Information on fuses, thermal cut-outs, and their reset procedures.

Machine Disposal and Recycling

Proper Machine Disposal

Guidelines for environmentally compliant disposal of the machine and its components.

Brush Selection and Usage

Polypropylene Brush (PPL) Selection

Details on using PPL brushes for general floor cleaning, including properties and applications.

Abrasive Brush Usage

Guidelines for using abrasive brushes on very dirty floors, with necessary precautions.

Brush Selection Chart

A table matching machine models with brush types, codes, and specifications.

Compliance and Declarations

EC Declaration of Compliance (SIMPLA 50 B;BT)

Manufacturer's declaration of compliance with EU directives for specific models.

EC Declaration of Compliance (SIMPLA 50 E)

Manufacturer's declaration of compliance with EU directives for a specific model.

COMAC SIMPLA 50 B Specifications

General IconGeneral
Solution tank40 L
Power supplyBattery
Voltage24 V
Working width500 mm
TractionSemiautomatic

Related product manuals