COMAC ANTEA 50 BT - User Manual

Questions and Answers

V
Victoria ArnoldAug 17, 2025
Why my COMAC Scrubber does not switch on?
- C
  Catherine VegaAug 17, 2025
  If your COMAC Scrubber isn't turning on, there could be several reasons. For B versions, ensure the main switch is in the work position with the LED illuminated and the ON symbol visible; if not, press the main switch. For BT versions, verify the main switch is set to "I" by turning the key a quarter turn to the right. If these steps don't resolve the issue, and the battery charge level is critical, perform a complete charging cycle. Also, ensure the power cable is disconnected from the battery charger. Finally, make sure the batteries are properly inserted into the machine.
M
Mary DavisAug 19, 2025
How to troubleshoot if my COMAC Scrubber does not switch on?
- A
  Alexis SmithAug 20, 2025
  If your COMAC Scrubber doesn't switch on, there might be several reasons. For B versions, ensure the main switch is in the work position with the LED on and the ON symbol visible; press the switch if it's not. For BT versions, check that the main switch is at “I”; turn the key a quarter turn to the right if it isn't. Also, for BT versions, check for alarm messages on the control display and contact a technician if there are any. Verify that the batteries are correctly connected and the battery connector is connected to the electrical system connector. Check the battery charge level and perform a complete charging cycle if it's low. Finally, if you have a CB system, disconnect the power cable from the battery charger.
J
Joseph GomezAug 22, 2025
What to do if the batteries on my COMAC Scrubber do not work correctly?
- M
  Marc WaltersAug 22, 2025
  If your COMAC Scrubber batteries aren't working correctly, start by ensuring the cable bridge is properly connected, and the output voltage is 24V. Also, inspect the battery terminals for oxidation. If they're oxidized, unplug all cables, clean the terminals, apply a bit of grease, and then reconnect the electrical connections.
C
christianmichaelAug 25, 2025
Why is the battery charger not working on my COMAC Scrubber?
- G
  gonzalezfrankAug 26, 2025
  If your COMAC Scrubber's battery charger isn't working, first, check that the power cable plug is correctly inserted into the socket on the battery charger (for versions with a CB system) and into the mains socket. Try a different socket if needed. Ensure the mains power supply characteristics match those required by the battery charger. Also, make sure the battery charger is connected to both the mains and the batteries.
V
Victoria MaxwellAug 27, 2025
Why does my COMAC Scrubber have a very low operating autonomy?
- P
  Phillip HerreraAug 28, 2025
  If your COMAC Scrubber has very low operating autonomy, check the battery charge level on the control display and complete a full charging cycle if the charge is low. Keep in mind that the batteries may need replacement if they have undergone many discharge and recharge cycles.
K
Kelsey TorresAug 30, 2025
What to do if the squeegee on my COMAC Scrubber does not dry perfectly?
- C
  Charles FranklinAug 31, 2025
  If the squeegee on your COMAC Scrubber is not drying perfectly, check for obstructions in the vacuum unit. Also, ensure that the cap on the recovery tank drainage tube and the recovery tank cover are correctly positioned.
Z
zwilsonSep 2, 2025
Why is my COMAC Scrubber not cleaning correctly?
- J
  james68Sep 2, 2025
  If your COMAC Scrubber is not cleaning correctly, ensure the brush is correctly inserted. Also, check that the brushes fitted on the appliance are suitable for the task. Inspect the brush bristles or the pad for excessive wear and replace if necessary.
J
Julie SantiagoSep 5, 2025
What should I do if my COMAC Scrubber does not move?
- D
  Daniel ChenSep 5, 2025
  If your COMAC Scrubber is not moving, ensure that the dead man's levers under the control handlebar are activated. For BT versions, gradually turn the potentiometer adjustment knob clockwise to regulate the appliance's speed. Also, for BT versions, engage the electric brake by turning the lever in the traction motor counter-clockwise.
C
Christopher SantosSep 8, 2025
Why is there insufficient detergent solution on the brushes of my COMAC Scrubber?
- D
  dsimmonsSep 8, 2025
  If there is insufficient detergent solution on the brushes of your COMAC Scrubber, make sure the detergent solution tap is not partially or completely closed; move the tap lever control knob downward to open it. Check that the quantity of detergent solution in the water system is sufficient for the work. Also, inspect the detergent solution filter for obstructions and clean it if necessary.
M
miguelsimsSep 12, 2025
Why is my COMAC Scrubber producing excessive foam?
- R
  rturnerSep 12, 2025
  If your COMAC Scrubber is producing excessive foam, ensure that you are using a low-foam detergent. If needed, add a small amount of anti-foam liquid to the recovery tank.

Summary

ANTEA Technical Data

VERSA Technical Data

General Safety Regulations

Appliance Safety

Type of Battery to be Used

Battery Maintenance and Disposal

Guidelines for maintaining and safely disposing of appliance batteries.

Inserting Batteries into the Device

Connecting Batteries to the System

Recharging Batteries (versions without built-in charger)

Recharging Batteries (versions with built-in battery charger)

Installing the Brush (ANTEA B - BT)

Brush Assembly (VERSA BT without PM)

Assembling the Squeegee

Preparing to Work

Starting Work (B versions)

Scrubbing and Drying (B versions)

Scrubbing Without Drying (B versions)

Drying (B versions)

Starting the Work Activities (versions BT - BTS - BTO)

Scrubbing and Drying (versions BT - BTS - BTO)

Scrubbing Without Drying (versions BT - BTS - BTO)

Drying Without Scrubbing (versions BT - BTS - BTO)

Emergency Switch (versions BT - BTS - BTO)

At the End of the Work

Recommended Maintenance Operations

Checking and Cleaning the Recovery Tank

Checking and Cleaning the Solution Tank Cap-Filter

Checking and Cleaning the Squeegee Unit

Adjusting the Squeegee Unit

Checking and Cleaning the Solution Tank

Brush Control and Maintenance (ANTEA B)

Brush Control and Maintenance (ANTEA BT)

Brush Control and Maintenance (VERSA 55-65 BT without PM)

Checking and Cleaning the Brush (BTS versions)

Cleaning the Water System (B versions)

Cleaning the Water System (BT - BTS - BTO versions)

Troubleshooting

Choosing and Using Brushes

COMAC ANTEA 50 BT Specifications

General

Working Width	500 mm
Solution Tank Capacity	40 L
Recovery Tank Capacity	60 L
Power Supply	Battery
Brush Motor Power	400 W
Vacuum Motor Power	400 W
Power Source	Battery
Battery Voltage	24 V
Brush Width	500 mm
Water Tank Capacity	40 L