Continental Girbau CG30-40 - User Manual

For replacement parts, contact the distributor
from which the dryer was purchased or
Continental Girbau, Inc.
®
2500 State Road 44
Oshkosh WI 54904
Telephone: (920) 231-8222 / Fax: (920) 231-4666
www.cont-girbau.com
030703JEV/wmarelli CGI Part No. A113170
CG30-40
(Gas/Electric/Steam)
Phase 7
Installation Manual
WARNING: For your safety the information in
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or death.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette notice
pour réduire au minimum le risque d’incendie
ou d’explosion ou pour éviter tout dommage
matériel, toute blessure ou la mort.
— Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides inflammables à
proximité de cet appareil ou de tout autre
appareil.
— QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
• Ne pas tenter d’allumer d’appareils.
• Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment.
• Évacuez la pièce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur
de gaz depuis un voisin. Suivez les
instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.
— L’installation et l’entretien doivent être assurés par
un installateur ou un service d’entretien qualifié
ou par le fournisseur de gaz.

Summary

SECTION I IMPORTANT INFORMATION

A. RECEIVING AND HANDLING

Details on inspecting and handling the dryer upon delivery to prevent transit damage.

B. SAFETY PRECAUTIONS

Essential safety warnings and precautions for operating and maintaining the dryer.

SECTION II SPECIFICATIONS;COMPONENT IDENTIFICATION

A. SPECIFICATIONS

Technical details including dimensions, weight, power requirements, and input ratings.

B. COMPONENT IDENTIFICATION

Identifies key components of the dryer through diagrams and labels.

SECTION III INSTALLATION PROCEDURES

A. LOCATION REQUIREMENTS

Guidelines for selecting an appropriate installation site, considering codes and clearances.

B. UNPACKING;SETTING UP

Instructions for safely removing the dryer from packaging and positioning it.

C. DRYER ENCLOSURE REQUIREMENTS

Specifies clearance dimensions and material requirements for dryer installations.

D. FRESH AIR SUPPLY REQUIREMENTS

Details the necessity and specifications for adequate make-up air for dryer operation.

E. EXHAUST REQUIREMENTS

Guidelines for proper dryer exhaust ducting, including size, length, and routing.

F. ELECTRICAL INFORMATION

Covers electrical connection requirements, wiring, and grounding for safety and compliance.

G. GAS INFORMATION

Pertains to gas supply connection, pressure, and safety regulations for gas dryers.

H. STEAM INFORMATION

Outlines steam supply requirements, pressure, coil PH levels, and connection details.

SECTION IV SERVICE;PARTS INFORMATION

A. SERVICE

Information on obtaining service, contacting qualified technicians, and required details.

B. PARTS

Guidance on ordering replacement parts, including necessary model and serial numbers.

SECTION V WARRANTY INFORMATION

A. WARRANTY

Information on obtaining a copy of the manufacturer's warranty bond and details needed.

B. RETURNING WARRANTY PARTS

Procedure for returning failed warranty items for evaluation, credit, or rejection.

SECTION VI ROUTINE MAINTENANCE

A. CLEANING

Schedule and procedures for cleaning the lint screen, lint chamber, and steam coil fins.

B. ADJUSTMENTS

Procedures for inspecting and adjusting various dryer components and safety devices.

C. LUBRICATION

Details on lubricating motor and bearing components, including part numbers for kits.

D. LINT DRAWER REMOVAL

Step-by-step instructions for removing and re-installing the dryer's lint drawer.

SECTION VII DATA LABEL INFORMATION

A. DATA LABEL

Explains the information found on the dryer's data label for service and identification.

SECTION VIII REVERSING TIMER SPIN;DWELL ADJUSTMENTS

SECTION IX PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS

SECTION X SENSOR ACTIVATED FIRE EXTINGUISHING (S.A.F.E.) SYSTEM

SYSTEM RESET

Procedure to reset the microprocessor after the S.A.F.E. system has been activated.

OPL S.A.F.E. SYSTEM CHECK PROCEDURE

Steps to test the functionality of the water solenoid valve for the S.A.F.E. system.

S.A.F.E. System Parts Break Down

Illustrated parts list and identification for the Sensor Activated Fire Extinguishing system.

Continental Girbau CG30-40 Specifications