What to do if there is a safety interrupt in Covaris E220 Laboratory Equipment?
A safety interrupt in Covaris Laboratory Equipment can occur due to several reasons: 1. The water tank might be misaligned. 2. The door could be open. 3. The STOP button might be depressed. 4. The safety interlock could be bypassed. To resolve this, check the tank alignment, ensure the door is closed properly, and verify the safety interlock.
Why does my Covaris Laboratory Equipment have incorrect positioning?
If you're experiencing incorrect positioning or inconsistent treatments with your Covaris Laboratory Equipment, it might be due to a lost home position or system misalignment. To fix this, home the system by selecting “initialize system” from the pull-down menu on the main panel, or by restarting SonoLab.
What to do if sample vessel hits the water jet nozzle in Covaris E220 Laboratory Equipment?
If the sample vessel hits the water jet nozzle in your Covaris Laboratory Equipment, it could be due to the system losing its home position or an incorrect nozzle position. To solve this: 1. Home the system. 2. Reposition the water jet manually.
How to fix Covaris Laboratory Equipment error message “Unknown Instrument Type”?
If you receive an “Unknown Instrument Type” error message with your Covaris Laboratory Equipment, it's likely due to incorrectly assigned device COM ports. To fix this, go to C:\Covaris\E-Series v6.2\Program to open the SonoLab configuration file, “SonoLab E-Series.ini”. Replace ComPortMotion=usb with ComPortMotion=COM4 and ComPortSound=usb with ComPortSound=COM3.
What to do if Covaris Laboratory Equipment shows error message that system not shut down correctly?
If you receive an error message stating that the Covaris Laboratory Equipment system was not shut down correctly, it means the SHUT DOWN command in Windows XP was not used before rebooting. Follow the instructions on the screen and use the SHUT DOWN command to resolve this.
Why is degassing system not generating bubbles in Covaris E220?
If the degassing system in your Covaris Laboratory Equipment isn't generating bubbles, it could be due to: 1. A clogged degassing dip tube. 2. The pump not working. Try these steps: 1. Remove the dip tube and backflush it under running water. 2. Examine the six holes (e.g., using a stereo microscope) to see if they are clogged, and use a pin to unclog them. 3. If the pump still doesn't run, contact Covaris.
Why are Dithering and Vertical Sweep values different in Covaris E220?
If the values for Dithering and Vertical Sweep in your Covaris Laboratory Equipment are different from what you entered, it means the values you entered are larger than the limits for a particular Well Plate. Use lower values to resolve this.
Why is there a delay in powering degassing pump on/off in Covaris Laboratory Equipment?
If you experience a delay in powering the degassing pump on/off in your Covaris Laboratory Equipment, it's likely because a method is currently running. Wait until the method completes before powering the degassing pump on or off.
What to do if the Covaris Laboratory Equipment safety interrupt occurs?
If a safety interrupt occurs with your Covaris Laboratory Equipment, check the water tank alignment, ensure the door is closed properly, verify the STOP button is not depressed, and make sure the door interlock is correctly engaged.
Why is the Covaris Laboratory Equipment homing/initialization not completing successfully?
The homing/initialization of your Covaris Laboratory Equipment may not be completing successfully due to a stage limit switch failure or the stage motor stalling. Ensure nothing obstructs stage movement.
Safety instructions for personnel operating the equipment.
Guidelines to avoid damaging the instrument during operation.
Instructions for correctly installing and filling the water bath.
Describes the acoustic transducer and its role in sample treatment.
Describes the water bath and the system for removing dissolved gases.
Explains the safety features that protect users from hazards.
Instructions for degasing the water bath for optimal performance.
Steps to load samples and start a treatment method.
How to stop, resume, or abort a running method.
Recommendations for daily and monthly water bath maintenance.
Care and handling instructions for the acoustic transducer.
Detailed steps for updating the RF Controller Board driver via Device Manager.
General| Brand | Covaris |
|---|---|
| Model | E220 |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
