What to do if Craftex Air Cleaner motor does not run when power is switched on?
If the motor of your Craftex Air Cleaner doesn't run when you switch it on, the fuse may have blown and needs replacing. Alternatively, the switch could be burned out, requiring replacement. Another potential cause is a loose or damaged wire connection, which should be tightened or replaced.
How to fix a shaking Craftex Air Cleaner?
If your Craftex Air Cleaner is shaking, it might not be properly anchored or secured; mount it securely in place. Another cause could be that the unit isn't level, so adjust it. Also, a worn or damaged motor can cause shaking, so check and replace the motor if necessary.
Why is my Craftex Air Cleaner motor overheating?
If the motor of your Craftex Air Cleaner is overheating, it could be due to using the wrong voltage. Check the voltage and the voltage label. Another possible reason is a damaged motor, which would need to be checked and replaced.
What to do if Craftex Air Cleaner has insufficient suction?
If your Craftex Air Cleaner isn't providing enough suction, the inlet port might be blocked, so try cleaning it. Also, the filter bag could be full; in that case, empty it. Finally, check if the outlet port is blocked and clean it, or adjust the outlet's direction.
How to prevent tooth breakage on my Craftex Saw?
If your Craftex Saw is experiencing tooth breakage, it could be due to several factors. You might be advancing too fast, so decrease the advance and use less cutting pressure. The cutting speed could be wrong, so change the disk speed and/or diameter. Ensure you're using a disk with the correct tooth pitch and of better quality. Check the gripping of the part in the vise. Remove any broken tooth parts left in the cut. Avoid resuming cutting on a previously made groove by turning the part. Check the level of lubricating liquid in the tank. Increase the flow of lubricating refrigerant, checking that the hole and the liquid outlet pipe are not blocked, and ensure the lubricating coolant is properly blended.
What causes premature disk wear on a Craftex CX909?
If the Craftex Saw disk is experiencing premature wear, several factors could be responsible. Ensure the disk was correctly run in, referring to the relevant chapter for guidance. The cutting speed might be incorrect, so adjust the disk speed and/or diameter. An unsuitable tooth profile or pitch could also be the cause, so select a suitable disk. Using a better quality disk may help. Also, ensure there is sufficient lubricating refrigerant by checking the level of the liquid in the tank. If the issue persists, increase the flow of lubricating refrigerant, ensuring that the hole and liquid outlet pipe are not blocked.
What causes a Craftex CX909 disk to chip?
If your Craftex Saw disk is chipping, it could be due to hardness, shape, or flaws in the material, so reduce the cutting pressure and/or the advance. The cutting speed might be wrong, so change the disk speed and/or diameter. Also, the tooth pitch might be wrong, so choose a suitable disk. Check the gripping of the part if there are vibrations. If the disk is incorrectly sharpened, replace it with one that is more suitable and correctly sharpened. Using a better quality disk might also solve the problem. Finally, check the percentage of water and oil in the emulsion if the lubricating refrigerant is incorrect.
Why is my Craftex Saw disk vibrating?
If the Craftex Saw disk is vibrating, it could be due to several reasons. The tooth pitch or tooth profile might be unsuitable, so choose a suitable disk. Ensure the part is gripped effectively in the vise. If the dimensions of the solid section are too large, abide by the instructions. If the disk diameter is incorrect or too large, decrease the disk diameter to match the part being cut.
What to do if the Craftex CX909 Saw blade sticks in the cut?
If the Craftex Saw blade is sticking in the cut, it could be due to several reasons. You might be advancing too quickly, so try decreasing the advance and using less cutting pressure. Alternatively, the cutting speed might be too low, so try increasing the speed. Ensure you're using a disk with a suitable tooth pitch. Check the blend of lubricating coolant and consider using a better quality disk if there's a sticky accumulation of material. Also, verify the level of lubricating refrigerant in the tank. If the issue persists, increase the flow of lubricating refrigerant, making sure the hole and liquid outlet pipe aren't blocked.
Why is my Craftex Lathe motor not running at full speed?
General| Type | Table Saw |
|---|---|
| Motor Power | 1.5 HP |
| Weight | 62 lbs |
| Blade Diameter | 10 inches |
| Bevel Capacity | 45 degrees |
To Next Page
