How to stop tools from grabbing on my Craftex Lathe?
If tools on your Craftex Lathe tend to grab or dig in, the issue could be due to dull tools (sharpen them), the tool support being set too low (reposition its height), the tool support being too far from the workpiece (reposition it closer), or using the wrong tool for the operation (use the correct tool).
Why does my Craftex Saw leave ridges on the cutting surface?
If your Craftex Saw is producing ridges on the cutting surface, several factors could be the cause. First, the disk diameter might be incorrect or too large; try decreasing the disk diameter to better match the part you're cutting. Also, ensure the part is gripped effectively in the vise. Reduce the advance and use less cutting pressure. If the disk teeth are worn, sharpen the tool. Check the level of lubricating refrigerant in the tank. Finally, make sure the blade has a larger tooth pitch to allow better unloading of shavings and hold more lubricating refrigerant.
Why is my Craftex CX101N disk vibrating?
If the Craftex Saw disk is vibrating, it could be due to several reasons. The tooth pitch or tooth profile might be unsuitable, so choose a suitable disk. Ensure the part is gripped effectively in the vise. If the dimensions of the solid section are too large, abide by the instructions. If the disk diameter is incorrect or too large, decrease the disk diameter to match the part being cut.
Why is my Craftex Power Tool spindle noisy?
A noisy spindle in your Craftex Power Tool could be due to damaged spindle bearings (replace the bearings) or a worn spindle (replace the spindle).
What to do if Craftex Lathe motor does not run when power switch is turned on?
If the motor doesn't run when you turn on the power switch, it could be due to a burnt-out switch, in which case you should replace the switch. Another possible cause is a loose or damaged connection wire, which needs to be tightened or replaced.
How to fix a Craftex Sander when the motor will not start?
If your Craftex Sander motor won't start, it could be due to a few reasons. First, a faulty or defective switch might be the issue; consider replacing it. Second, a faulty or blown capacitor could be the culprit, so replace the capacitor. Third, check for a blown fuse or tripped circuit breaker; if a fuse is blown, replace it with the required size, and if a breaker is tripped, reset it. Finally, low line voltage could be the cause; check the power supply for the correct voltage and adjust as needed.
Why is the board edge curved after using my Craftex Power Tool?
This can happen if the board isn't held with the same pressure on the infeed and outfeed table during the cut; ensure you hold the board with consistent pressure as it moves over the cutterhead. Also, if the board has too much bow or coil along its length, take limited cuts to remove the high spots before a full pass. Surface plane one face so there is a good surface to place along the fence. It should take 3 to 5 passes to get a perfect edge depending on the state of the board and the depth of cut.
Why is my Craftex Power Tool causing chipped or ripped out pieces?
This issue can be caused by knots or incompatible grain direction in the wood. Check the workpiece for knots and grain; clean stock should be used. Also, nicked or broken cutter inserts can be the problem; turn or replace the cutter insert. Feeding the workpiece too fast can also cause this; reduce the feed rate. Finally, taking too deep of a cut can cause chipping; take a smaller depth in cut, especially when using hard wood.
What to do if Craftex Air Cleaner motor does not run when power is switched on?
If the motor of your Craftex Air Cleaner doesn't run when you switch it on, the fuse may have blown and needs replacing. Alternatively, the switch could be burned out, requiring replacement. Another potential cause is a loose or damaged wire connection, which should be tightened or replaced.
Why Craftex Air Cleaner motor will not reach full power?
If your Craftex Air Cleaner motor won't reach full power, the power wiring might be incorrect; replace or correct it. Another possibility is that an overload has tripped; reduce the load by cleaning the filters as necessary.
To Next Page
General
