Craftsman 107.10265 - User Manual

Questions and Answers

J
Jennifer HarveyAug 15, 2025
What to do if my Craftsman 107.10265 does not run?
- B
  Brenda AllenAug 15, 2025
  If your Craftsman Air Compressor isn't running, make sure it's properly plugged in and the power switch is in the ON position. Also, check for blown fuses (replace if necessary) or tripped breakers (reset and investigate the cause). If the thermal overload is open, unplug the compressor and wait for it to cool down before it restarts. If none of these steps work, the pressure switch may need to be replaced. If the tank is full, the compressor will start, when tank pressure drops to cut-in pressure.
M
Mary SmithAug 18, 2025
Why does my Craftsman 107.10265 keep blowing fuses or tripping the circuit breaker?
- R
  rachelsmithAug 18, 2025
  If your Craftsman Air Compressor is experiencing repeated fuse blowing or circuit breaker tripping, first ensure the fuse or breaker at the power supply is the correct size and type. Use only time-delay fuses. To avoid overloading a circuit, disconnect other electrical appliances or operate the compressor on its own branch circuit. Also, ensure you are using the correct wire gauge and length of extension cord. If the problem persists, the unloader or check valve may be defective, requiring service.
K
Katelyn HoffmanAug 21, 2025
Why does the air pressure drop when my Craftsman Air Compressor shuts off?
- P
  Patrick MoralesAug 22, 2025
  If the air receiver pressure drops when your Craftsman Air Compressor shuts off, check all connections (fittings, tubing, etc.) for leaks using soapy water; tighten any loose connections until the leak stops. Also, ensure the drain valve is tightened. If the issue persists, the check valve may be leaking, and you should take the compressor to a service center.
P
Paige PhillipsAug 25, 2025
Why is my Craftsman 107.10265 Air Compressor motor humming but not running?
- L
  lisahopkinsAug 26, 2025
  If your Craftsman Air Compressor motor hums but doesn't run or runs slowly, check the voltage from the power supply with a voltmeter. Ensure you're using the correct wire gauge and length of extension cord. If these steps don't resolve the issue, the motor winding may be shorted or broken, or the unloader or check valve may be defective, requiring you to take the compressor to a service center.
A
Alexander FrankAug 28, 2025
Why does my Craftsman Air Compressor run continuously?
- J
  Jessica Coleman DVMAug 29, 2025
  If your Craftsman Air Compressor runs continuously, first ensure the tank drain valve is closed. If it is closed and the compressor continues to run, the pressure switch may be defective, requiring you to take the compressor to a service center. Also, consider if the usage is excessive; if so, decrease the amount of tool run-time because the compressor may not be large enough to supply the air requirement of the tool.
G
Gregory GarciaSep 1, 2025
Why does the thermal overload protector keep cutting out on my Craftsman 107.10265?
- K
  Kristi NelsonSep 1, 2025
  If the thermal overload protector on your Craftsman Air Compressor cuts out repeatedly, check the voltage from the power supply with a voltmeter. Ensure the compressor is in a well-ventilated area to prevent overheating. Also, verify that you're using the correct gauge wire and cord length.
B
Becky HermanSep 4, 2025
How to reduce moisture in the air discharge of my Craftsman 107.10265?
- P
  Paul MirandaSep 4, 2025
  To reduce excessive moisture in the air discharge from your Craftsman Air Compressor, start by draining the tank to remove any accumulated water. If the humidity is high, move the compressor to an area with less humidity or use an air line filter to reduce moisture discharge in the tank.
P
Preston AndersonSep 8, 2025
What to do if air is leaking from my Craftsman Air Compressor?
- M
  Makayla WelchSep 8, 2025
  If air is leaking from your Craftsman Air Compressor, first ensure all hose connections are sealed with thread sealing tape and tightened properly. If the leak persists, inspect the air hose for breaks or damage and replace it if necessary.
M
martinezryanSep 12, 2025
How to fix a vibrating Craftsman 107.10265 Air Compressor?
- M
  Michael TorresSep 12, 2025
  If your Craftsman Air Compressor vibrates, tighten the mounting bolts.