To Next PageTo Next Page
Need help?Do you have a question about the Craftsman 113.298722 and is the answer not in the manual?
Steps and checks to perform before operating the table saw.
Guidelines for safely installing and moving the table saw.
Checks to perform before each use of the table saw.
Safety measures to prevent jams, slips, kickbacks, and throwbacks.
Guidelines for maintaining a clean and safe work area.
Steps for planning cuts and preparing for safe operation.
Recommended clothing and safety gear for operating the saw.
Safety precautions to follow when the saw blade is spinning.
Steps to take before leaving the saw unattended.
Specific safety advice for performing rip type cuts.
Specific safety advice for performing cross cut type cuts.
Instructions for safely connecting the saw to an electrical outlet.
Procedure to check and ensure correct motor rotation direction.
List of tools required for assembling the table saw.
Instructions for attaching the elevation and tilt handwheels.
Procedure to ensure the table insert is flush with the table top.
Ensuring the saw blade is perfectly perpendicular to the table.
Instructions for assembling the steel legs for the saw base.
Procedure for attaching the saw unit to the assembled legs.
Instructions for attaching the cast iron table extensions.
Procedure for installing the ON-OFF power switch assembly.
Attaching the front guide bar for the rip fence assembly.
Attaching the rear guide bar for the rip fence assembly.
Steps to ensure the rip fence is parallel to the saw blade.
Adjusting the spring for proper rip fence self-alignment.
Adjusting the rip fence lock lever for secure operation.
Fine-tuning rip fence parallelism to the blade and miter gauge.
Setting the rip scale pointer to the '0' mark for accurate measurements.
Procedure for attaching the blade guard and spreader assembly.
Steps for positioning and mounting the saw motor.
Aligning the motor correctly on its mounting base.
Attaching the motor to the motor base assembly.
Procedure for installing and tensioning the drive belt.
Instructions for installing the belt guard on model 113.298722.
Instructions for installing the belt guard on model 113.298762.
Connecting the motor power cord to the electrical outlet.
Explanation of the saw's ON-OFF switch and its safety features.
How to use the handwheel to raise or lower the saw blade.
How to use the handwheel to tilt the saw blade for bevel cuts.
How to lock the saw blade at a desired tilt position.
How to position and lock the rip fence for ripping operations.
How to use the miter gauge for crosscutting and mitering.
Importance and use of the blade guard for thru-sawing.
Information on the removable table insert.
Procedure for safely changing the table saw blade.
How to use the Exact-I-Cut disc for accurate cuts.
Detailed checks and inspections before operating the saw.
Strategies to prevent workpiece binding and violent ejection.
Introduction to jigs and fixtures for accurate workpiece feeding.
Instructions for making and using push sticks and blocks.
Instructions for making and using an auxiliary fence or work support.
How to perform crosscuts using the miter gauge.
Techniques for cutting multiple identical pieces.
How to perform angled cuts using the miter gauge.
Specific safety precautions for rip cutting operations.
How to perform cuts along the length of the workpiece.
Using featherboards to guide work during thru-sawing.
How to rip a board to reduce its thickness.
Instructions for using the dado head for cutting grooves.
Instructions for using the molding head for shaping.
Using featherboards for non-thru cuts with miter gauge.
Adjusting the miter gauge for accuracy and proper alignment.
Aligning the saw blade parallel to the miter gauge groove.
Ensuring the blade is square (90°) to the table and adjusting tilt.
Adjusting the tilt handwheel mechanism for smooth operation.
Recommended lubrication points and types for the saw.
List of recommended accessories for the table saw.
List of parts for Figure 1 diagram.
List of parts for Figure 2 diagram.
List of parts for the ON-OFF power outlet assembly.
List of parts for table extensions.
List of parts for the rip fence assembly.
List of parts for the miter gauge assembly.
List of parts for the blade guard assembly.
List of parts for the leg set assembly.
Guidelines for ordering replacement parts for the table saw.
General