To Next PageTo Next PageWhat causes an uneven cut with my Craftsman 247.203690 Lawn Mower?
If your Craftsman Lawn Mower is giving an uneven cut, it might be because the deck isn't leveled properly; perform a side-to-side deck adjustment. A dull blade can also cause this, so sharpen or replace it. Finally, check the tire pressure in all four tires, as uneven pressure can contribute to an uneven cut.
Why is my Craftsman 247.203690 Lawn Mower engine running erratically?
If your Craftsman Lawn Mower engine runs erratically, it could be due to several reasons. First, check if the choke is activated and deactivate it. Ensure the spark plug wires are securely connected. A blocked fuel line or stale fuel can also cause this issue; replace the fuel line, use fresh gasoline, and replace the fuel filter. The vent in the gas cap might be plugged, so clear it or replace the cap if damaged. Water or dirt in the fuel system can also be a factor; drain the fuel tank and refill with fresh gasoline. Lastly, a dirty air cleaner can cause erratic running, so replace the air cleaner paper element or clean the foam pre-cleaner, if your mower has one.
What to do if my Craftsman Lawn Mower has excessive vibration?
If your Craftsman Lawn Mower is vibrating excessively, it could be due to a loose or unbalanced cutting blade, so try tightening the blade and spindle. Alternatively, the cutting blade may be damaged or bent, in which case you should replace it.
Why is my Craftsman 247.203690 Lawn Mower engine overheating?
If your Craftsman Lawn Mower engine is overheating, it could be due to a low engine oil level. Fill the crankcase with the correct amount and weight of oil. Alternatively, airflow might be restricted. Clean any grass clippings and debris from around the engine’s cooling fins and housing.
Why isn't my Craftsman Lawn Mower mulching grass?
If your Craftsman Lawn Mower isn't mulching grass effectively, make sure the engine speed is set high by placing the throttle in the FAST position. Avoid mulching when the grass is wet. If the grass is excessively high, mow once at a higher cutting height, then mow again at the desired height, or reduce the cutting swath. Also, check the blade; a dull blade should be sharpened or replaced.
General| Brand | Craftsman |
|---|---|
| Model | 247.203690 |
| Category | Lawn Mower |
| Language | English |
Provides contact information and procedures for obtaining warranty service.
Outlines fundamental safety rules for operating the equipment and using the manual.
Provides critical safety guidelines for operating the tractor on slopes.
Details procedures for safely handling and storing gasoline.
General safety rules to follow before performing any maintenance or repairs.
Warns against modifying the engine governor settings to prevent unsafe speeds.
Explains the meaning of various safety symbols found on the equipment and in the manual.
Provides detailed descriptions of safety symbols related to operation and hazards.
Step-by-step instructions on how to use the provided slope gauge for safe operation.
Reiterates the dangers of operating on slopes exceeding 12 degrees.
Guides the user through installing the steering wheel and associated components.
Provides safety procedures for connecting the tractor's battery cables.
Details the procedure for checking the engine oil level before operation.
Outlines safe practices for refueling the tractor's fuel tank.
Identifies key controls and their locations on the tractor's dashboard and console.
Explains how to engage and disengage the cutting deck blades using the PTO lever.
Details the tractor's safety interlock system preventing unintended operation.
Step-by-step procedure for starting the tractor's engine safely.
Provides instructions for safely shutting down the tractor's engine.
Specific safety instructions for operating the tractor on inclines.
A table outlining recommended periodic maintenance tasks and intervals.
Detailed steps for checking and changing the engine oil.
Procedures for removing, sharpening, balancing, and replacing the cutting blade.
Steps to prepare the engine for long-term storage, including fuel treatment.
Procedure to completely empty the fuel tank and lines to prevent deterioration.
Common causes and remedies for the engine failing to start.
Diagnoses for issues causing the engine to run erratically or overheat.
