To Next PageTo Next PageWhy does my Craftsman 247.290000 Lawn Mower produce an uneven cut?
An uneven cut with your Craftsman Lawn Mower can be caused by: * The deck not being leveled properly. Perform a side-to-side deck adjustment. * A dull blade. Sharpen or replace the blade. * Uneven tire pressure. Check the tire pressure in all four tires.
What causes my Craftsman Lawn Mower engine to idle rough?
Rough idling in your Craftsman Lawn Mower engine could stem from: * A spark plug that is fouled, faulty, or has a gap that's too wide. Replace the spark plug and set the plug gap. * A dirty air cleaner. Replace the air cleaner element and/or clean the pre-cleaner.
How to fix a Craftsman 247.290000 engine that hesitates at high RPM?
If your Craftsman Lawn Mower engine hesitates at high RPM, it might be due to: * A spark plug gap that is too close. Remove the spark plug and reset the gap.
Why is my Craftsman 247.290000 Lawn Mower engine running erratically?
Your Craftsman Lawn Mower engine might be running erratically due to several reasons: * The choke might be activated. Deactivate the choke. * Spark plug wires might be loose. Connect the spark plug wires. * The fuel line might be blocked, or the fuel might be stale. Replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. * The vent in the gas cap might be plugged. Clear the vent or replace the cap if damaged. * There might be water or dirt in the fuel system. Drain the fuel tank and refill with clean, fresh gasoline. * The air cleaner might be dirty. Replace the air cleaner paper element or clean the foam pre-cleaner, if equipped.
What causes my Craftsman Lawn Mower engine to overheat?
Several factors can cause a Craftsman Lawn Mower engine to overheat: * Low engine oil level. Fill the crankcase with the proper amount and weight of oil. * Restricted airflow. Clean grass clippings and debris from around the engine’s cooling fins and housing.
What to do if my Craftsman Lawn Mower will not mulch grass?
If your Craftsman Lawn Mower is not mulching grass effectively, here are a few potential causes and solutions: * Engine speed might be too low. Place the throttle in the FAST position. * The grass might be wet. Avoid mulching when the grass is wet. * The grass might be excessively high. Mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. * The blade might be dull. Sharpen or replace the blade.
Why is my Craftsman 247.290000 Lawn Mower experiencing excessive vibration?
Excessive vibration in your Craftsman Lawn Mower can be attributed to: * A cutting blade that is loose or unbalanced. Tighten the blade and spindle. * A damaged or bent cutting blade. Replace the blade.
General| Brand | Craftsman |
|---|---|
| Model | 247.290000 |
| Category | Lawn Mower |
| Language | English |
Essential procedures and precautions for operating the riding mower safely.
Specific safety rules and guidelines for operating the mower on sloped terrain.
Rules and warnings regarding children's safety around the operating mower.
Guidelines and warnings for safely towing attachments with the riding mower.
Safety measures for handling gasoline and performing general maintenance.
Information on emission regulations and the use of spark arrestors.
Explanations of safety symbols used in the manual and on the equipment.
Instructions on how to use the slope gauge to determine safe mowing slopes.
Lists items included in the crate, hardware pack, and recommended tools for assembly.
Step-by-step instructions for attaching the steering wheel assembly to the tractor.
Detailed procedure for securing the seat to the tractor's mounting bracket.
Guidance on adjusting seat position and steering wheel height for operator comfort.
Steps for installing the deck chute and rear engine cover for proper operation.
Instructions for attaching the rear hitch plate and front bumper.
Procedure for correctly connecting the tractor's battery cables to the terminals.
Instructions for checking oil levels and understanding fuel requirements before operation.
Guidance on filling the fuel tank and setting the correct tire pressure.
Identifies and labels the various controls on the tractor's operator panel.
Explains the function of essential controls like throttle, ignition, and shift levers.
Details the use of the deck lift, PTO engagement, and safety interlock switches.
Procedures for starting, stopping the engine, engaging the parking brake, and setting cutting height.
Instructions for driving the tractor and safely operating on inclines and slopes.
Guidance on engaging the cutting blades and best practices for mowing.
Outlines required service intervals and tasks for maintaining the tractor.
Procedures for checking, draining, and replacing engine oil and oil filter.
Instructions for cleaning/replacing the air filter and servicing the spark plug.
Guidance on replacing the fuel filter and general fuel system checks.
Steps for cleaning the engine/deck and removing the cutting deck.
Procedures for inspecting and servicing cutting blades, tires, and changing the deck belt.
Covers deck leveling, parking brake, battery maintenance, and charging.
Details on where and how to lubricate various moving parts of the tractor.
Steps to prepare the engine for long-term storage to prevent deterioration.
Instructions for draining fuel, cleaning the tractor, and preparing for storage.
Diagnoses and remedies for common engine problems like failure to start or erratic running.
Solutions for issues such as excessive vibration, poor mulching, or uneven cutting.
Outlines the owner's duties regarding maintenance and proper use of the equipment.
Explains warranty scope, duration, and lists covered emission-related parts.
Details the advantages and services included with the extended repair agreement.
Information on how to schedule service and contact customer support for the agreement.
