What causes uneven cut with Craftsman Lawn Mower?
An uneven cut with your Craftsman Lawn Mower may result from: * The deck not being leveled properly. Perform a side-to-side deck adjustment. * A dull blade. Sharpen or replace the blade. * Uneven tire pressure. Check the tire pressure in all four tires.
What to do if Craftsman 247.28884 engine idles rough?
A rough idling Craftsman Lawn Mower engine could be caused by: * A spark plug that is fouled, faulty, or has a gap that is too wide. Replace the spark plug and set the plug gap. * A dirty air cleaner. Replace the air cleaner element and/or clean the pre-cleaner.
Why does my Craftsman 247.28884 engine run erratically?
An erratic running engine in your Craftsman Lawn Mower can stem from: * The unit running with the CHOKE activated. Deactivate the CHOKE. * Loose spark plug wires. Connect the spark plug wires. * A blocked fuel line or stale fuel. Replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. * A plugged vent in the gas cap. Clear the vent or replace the cap if damaged. * Water or dirt in the fuel system. Drain the fuel tank and refill with clean, fresh gasoline. * A dirty air cleaner. Replace the air cleaner paper element or clean the foam pre-cleaner, if equipped.
Why Craftsman Lawn Mower engine overheats?
Your Craftsman Lawn Mower engine may overheat because: * The engine oil level is low. Fill the crankcase with the proper amount and weight of oil. * Air flow is restricted. Clean grass clippings and debris from around the engine’s cooling fins and housing.
Why does Craftsman 247.28884 engine hesitate at high RPM?
If your Craftsman Lawn Mower engine hesitates at high RPM, it could be because the spark plug gap is too close. Remove the spark plug and reset the gap.
What to do if Craftsman 247.28884 Lawn Mower is not mulching grass?
If your Craftsman Lawn Mower isn't mulching grass effectively: * Ensure the engine speed isn't too low by placing the throttle in the FAST (rabbit) position. * Avoid mulching when the grass is wet. * If the grass is excessively high, mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. * Check if the blade is dull; sharpen or replace it.
How to fix excessive vibration in Craftsman Lawn Mower?
Excessive vibration in your Craftsman Lawn Mower can be due to: * A loose or unbalanced cutting blade. Tighten the blade and spindle. * A damaged or bent cutting blade. Replace the blade.
Why Craftsman Lawn Mower engine fails to start?
Your Craftsman Lawn Mower engine might fail to start due to several reasons: * The PTO/Blade Engage lever may be engaged. If so, place the lever in the disengaged (OFF) position. * The parking brake might not be engaged. Engage the parking brake. * Spark plug wires could be disconnected. Connect the wires to the spark plugs. * The Throttle/Choke control lever might not be in the correct starting position. Place the Throttle/Choke lever into the FAST position. * The choke may not be activated. Move the Throttle/Choke lever into the Choke position. * The fuel tank could be empty or contain stale fuel. Fill the tank with clean, fresh (less than 30 days old) gas. * The fuel line may be blocked. Replace the fuel line and the fuel filter. * The spark plugs could be faulty. Clea...
Details about engine oil, fuel, spark plug, and engine type.
Section to record model number, serial number, and date of purchase.
Read, understand, and follow all instructions on the machine and in the manual.
Guidance and warnings for operating the tractor on inclines to prevent accidents.
Safety precautions for children, towing, and keeping bystanders safe.
Safety measures during maintenance, including handling gasoline.
Explains safety symbols and provides a slope determination guide.
Instructions for connecting the battery cables to the tractor.
Steps to attach the steering wheel to the tractor.
How to adjust and attach the seat, and tire pressure recommendations.
Identifies and describes the tractor's main controls and their functions.
Step-by-step guide to safely start and stop the tractor's engine.
Instructions on how to drive and mow safely, including blade engagement.
Recommended service intervals for various tractor components.
Procedures for checking and changing engine oil and oil filter.
Procedures for adjusting the cutting deck for proper height and balance.
Instructions for servicing cutting blades and changing the deck belt.
Steps to prepare the engine and fuel system for long-term storage.
Cleaning and lubricating the tractor before storing it.
Common causes and remedies for an engine that fails to start.
Solutions for erratic engine operation, overheating, and mowing problems.
Exploded view and list of chassis, body, and fender components.
Exploded view and parts list for major engine components.
Parts list and diagrams for the cutting deck assembly.
Outlines owner's duties for maintenance and warranty claims.
Details specific parts covered and warranty terms for emissions control.
General| Engine | Briggs & Stratton |
|---|---|
| Drive Type | Self-Propelled |
| Cutting Positions | 6 |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Side Discharge Capability | Yes |
| Speed Settings | Variable |
| Cutting Width | 21 inches |
| Drive System | Rear Wheel Drive |
| Cutting Height | 1.25 to 3.75 inches |
| Wheel Size | 8 inches |
To Next Page