Why is my Craftsman Snow Blower experiencing excessive vibration?
If your Craftsman Snow Blower is vibrating excessively, immediately stop the engine and disconnect the spark plug wire. Tighten all bolts and nuts. If the vibration continues, have the unit serviced by a Sears Parts & Repair Center.
Why does my Craftsman 247.888701 engine fail to start?
There are several reasons why your Craftsman Snow Blower might not be starting: * The choke control may not be in the CHOKE position, so move it accordingly. * The spark plug wire might be disconnected; ensure it's connected. * The spark plug could be faulty and needs cleaning, gap adjustment, or replacement. * The fuel tank might be empty or contain stale fuel; refill with fresh gasoline. * The engine may not be primed; prime it as instructed in the Operation section. * The safety key might not be inserted; insert it fully into the switch. * The extension cord might not be connected (if your model has an electric start button); connect it to a grounded outlet.
Why my Craftsman Lawn Mower engine fails to start?
If your Craftsman Lawn Mower engine won't start, possible causes include: the PTO/Blade Engage knob is engaged (place it in the disengaged/OFF position), the parking brake isn't engaged (engage it), the spark plug wire is disconnected (connect it), the throttle control lever isn't in the correct starting position (place the Throttle lever to FAST position), the fuel tank is empty or the fuel is stale (fill the tank with clean, fresh gas that is less than 30 days old), the fuel line or fuel filter is blocked (replace the fuel line; replace the fuel filter), the spark plug is faulty (clean, adjust the gap, or replace the plug), the engine is flooded (crank the engine with the throttle in FAST position), or a fuse is blown (replace the fuse).
How to reduce vibration on my Craftsman Lawn Mower?
Excessive vibration in your Craftsman Lawn Mower can stem from: * A loose or unbalanced cutting blade: Tighten the blade and adapter, and balance the blade. * A bent cutting blade: Replace the blade.
Why won't my Craftsman Lawn Mower engine start?
There are several reasons why your Craftsman Lawn Mower engine might fail to start: * The PTO/Blade Engage knob may be engaged. Ensure it is in the disengaged (OFF) position. * The parking brake may not be engaged. Engage the parking brake. * The spark plug wire may be disconnected. Connect the wire to the spark plug. * The throttle control lever may not be in the correct starting position. Place the throttle lever to the FAST position. * The fuel tank may be empty or contain stale fuel. Fill the tank with clean, fresh gas (less than 30 days old). * There may be a blocked fuel line or fuel filter. Replace the fuel line. Replace the fuel filter. * The spark plug may be faulty. Clean, adjust the gap, or replace the plug. * The engine may be flooded. Crank the engine with the...
Why doesn't the chute on my Craftsman 247.888701 Snow Blower easily rotate 180-200 degrees?
If the chute on your Craftsman Snow Blower doesn't easily rotate, it might be assembled incorrectly. Disassemble the chute control and reassemble it as directed in the Assembly section.
What to do if Craftsman Lawn Mower engine runs erratic?
If your Craftsman Lawn Mower engine runs erratically, it could be due to: - A loose spark plug boot. Connect and tighten the spark plug boot. - Stale fuel. Replace the fuel with clean, fresh gasoline. - A plugged vent in the gas cap. Clear the vent. - Water or dirt in the fuel system. Run the engine until it stops due to lack of fuel, then refill with fresh fuel. - A dirty air cleaner. Refer to the Air Cleaner Maintenance section in the Engine Manual.
Why Craftsman Lawn Mower has uneven cut?
An uneven cut with your Craftsman Lawn Mower can result from: - Wheels not positioned correctly. Adjust the cutting height lever on the right front and right rear wheel to the same position. - A dull blade. Sharpen or replace the blade.
Why Craftsman Lawn Mower has excessive vibration?
Excessive vibration in your Craftsman Lawn Mower could be due to: - A loose or unbalanced cutting blade. Tighten the blade and adapter, and balance the blade. - A bent cutting blade. Replace the blade.
Why is my Craftsman Snow Blower not throwing snow?
If your Craftsman Snow Blower is not discharging snow, first, immediately stop the engine and disconnect the spark plug wire. Check the chute assembly for clogs and clean it, along with the inside of the auger housing, using a clean-out tool. Also, check for any foreign objects lodged in the auger and remove them with the clean-out tool. If these steps don't resolve the issue, the auger cable may need adjustment or the auger belt may be loose or damaged. In that case you should refer to the Assembly section or Service and Maintenance section. Another possibility is that the shear pins have sheared, requiring replacement; refer to the Operation section for instructions.
General| Product Type | Two-Stage Snow Blower |
|---|---|
| Clearing Width (in) | 24 |
| Fuel Type | Gasoline |
| Throwing Distance | Up to 40 ft |
| Intake Height (in) | 21 |
| Forward Speeds | 6 |
| Reverse Speeds | 2 |
| Auger Material | Steel |
| Tire Size (in) | 13 x 4 |
| Engine | 208cc |
| Start Type | Electric |
To Next Page