EasyManua.ls Logo

Craftsman 580.752130 - User Manual

Craftsman 580.752130
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
2550 PSI MAX
2.3 GPM MAX
PRESSURE WASHER
CLEANING SYSTEM
Operator’s Manual
Model No. 580.752130
Part No. 203771GS Draft - (04/18/2007)
• Safety
• Assembly
• Operation
• Maintenance
• Parts
• Español, p. 34
HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)
PRESSURE WASHER
CUSTOMER HELPLINE
1-800-222-3136
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.craftsman.com
ADVERTENCIA
Antes de utilizar el producto, lea este
manual y siga todas las Reglas de
Seguridad e Instrucciones de Uso.
WARNING
Before using this product, read this
manual and follow all Safety Rules
and Operating Instructions.

Questions and Answers

  • S
    Susan BeasleyAug 11, 2025
    Why won't my Craftsman 580.752130 engine start or why does it start and run rough?
    • T
      Thomas LopezAug 11, 2025
      If your Craftsman Pressure Washer engine won't start or runs rough, here are a few things to check: * Make sure the air cleaner is clean; if it's dirty, clean or replace it. * Ensure the fuel tank isn't empty; if it is, fill it. * If the fuel is stale, drain the tank and refill with fresh fuel. * Confirm the spark plug wire is connected to the spark plug; if not, connect it. * If the spark plug is bad, replace it. * If there's water in the fuel, drain the tank and refill with fresh fuel.
  • C
    Charles MckenzieAug 16, 2025
    How to troubleshoot a Craftsman 580.752130 Pressure Washer that has failure to produce pressure?
    • D
      Dalton MendozaAug 16, 2025
      If your Craftsman Pressure Washer fails to produce pressure, consider the following possible causes and solutions: * If a low pressure spray tip is installed, replace it with a high pressure spray tip. * If the water inlet is blocked, clear it. * If the water supply is inadequate, provide adequate water flow. * If the inlet hose is kinked or leaking, straighten the hose or patch the leak. * If the inlet hose strainer is clogged, check and clean it. * If the water supply is over 100°F, provide a cooler water supply. * If the high pressure hose is blocked or leaks, clear the blockage or replace the hose. * If the gun leaks, replace it. * If the nozzle is obstructed, clean it.
  • C
    Christopher ClarkAug 22, 2025
    What to do if Craftsman Pressure Washer engine shuts down during operation?
    • A
      Austin RamirezAug 22, 2025
      If the engine of your Craftsman Pressure Washer shuts down during operation, the most likely cause is that it is out of fuel. Simply fill the fuel tank to resolve this issue.
  • C
    Casey SimmonsAug 28, 2025
    Why is detergent not mixing with spray in my Craftsman Pressure Washer?
    • M
      Meredith ThompsonAug 28, 2025
      If the detergent fails to mix with the spray of your Craftsman Pressure Washer, check these two things: * Make sure the detergent shut-off valve is in the “On” position. If it’s off, rotate it to “On”. * If a high pressure spray tip is installed, replace it with a low pressure spray tip.
  • R
    Renee MarquezSep 4, 2025
    What to do if Craftsman 580.752130 engine bogs when load is added?
    • K
      Krystal StuartSep 4, 2025
      If the engine of your Craftsman Pressure Washer runs well without a load but bogs down when a load is added, the engine speed may be too slow. Move the throttle control to the FAST position.

Craftsman 580.752130 Specifications

General IconGeneral
Power SourceGasoline
Hose Length25 ft
Engine Displacement190 cc
Engine Type4-Cycle OHV
Pump TypeAxial cam
Soap ApplicatorYes
WheelsYes
Nozzles Included0°, 25°, Soap

Related product manuals