EasyManua.ls Logo

Craftsman 580.752101 - User Manual

Craftsman 580.752101
56 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
2700 PSI MAX
2.5 GPM MAX
PRESSURE WASHER
CLEANING SYSTEM
Operator’s Manual
Model No. 580.752101
Part No. 203843GS Draft - (05/07/2007)
• Safety
• Assembly
• Operation
• Maintenance
• Parts
• Español, p. 32
HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)
PRESSURE WASHER
CUSTOMER HELPLINE
1-800-222-3136
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.craftsman.com
ADVERTENCIA
Antes de utilizar el producto, lea este
manual y siga todas las Reglas de
Seguridad e Instrucciones de Uso.
WARNING
Before using this product, read this
manual and follow all Safety Rules
and Operating Instructions.

Table of Contents

Questions and Answers

  • D
    Donna WoodAug 9, 2025
    Why does my Craftsman Pressure Washer engine not start or run rough?
    • L
      larry61Aug 9, 2025
      If your Craftsman Pressure Washer engine won't start or runs roughly, here are a few things to check: * The air cleaner might be dirty, so try cleaning or replacing it. * Make sure you have enough fuel in the tank, and that the fuel isn't stale. If it is, drain the tank and refill with fresh fuel. * Ensure the spark plug wire is properly connected to the spark plug. Also, the spark plug itself might be bad and need replacing. * If there's water in the fuel, drain the tank and refill it with fresh fuel. * Avoid overchoking; open the choke fully and crank the engine. * If the fuel mixture is excessively rich, contact a Sears service facility.
  • C
    Christopher MartinezAug 14, 2025
    How to fix a Craftsman 580.752101 Pressure Washer that is failing to produce pressure?
    • D
      David WadeAug 14, 2025
      If your Craftsman Pressure Washer isn't producing pressure, try the following: * Ensure the PrecisionSpray™ Selector is set to a high-pressure position. * Check for and clear any blockages in the water inlet. * Make sure there's an adequate water supply. * Straighten any kinks in the inlet hose and repair any leaks. * Inspect and clean the inlet hose strainer. * Verify the water supply temperature is not over 100°F; use a cooler water supply. * Clear any blockages in the high-pressure hose or replace it if it leaks. * Replace the gun if it leaks. * Clean any obstructions in the PrecisionSpray™ Selector nozzles. * If the pump is faulty, contact a Sears service facility.
  • W
    williamsashleyAug 25, 2025
    How to get detergent to mix with the spray on my Craftsman 580.752101?
    • E
      Erin OwensAug 25, 2025
      If detergent isn't mixing with the spray from your Craftsman Pressure Washer: * Make sure the detergent shut-off valve is in the “On” position. * Ensure the PrecisionSpray™ Selector is in a low-pressure position.
  • D
    Dale KingAug 29, 2025
    What to do if choke is opened too soon on Craftsman 580.752101 Pressure Washer?
    • J
      John JacksonAug 29, 2025
      Move the choke to the halfway position until the engine runs smoothly on your Craftsman Pressure Washer.
  • D
    Daniel BeckerSep 2, 2025
    What to do if Craftsman Pressure Washer is out of fuel?
    • J
      julieruizSep 2, 2025
      Fill the fuel tank of your Craftsman Pressure Washer.
  • M
    Matthew HendrixSep 10, 2025
    What to do if my Craftsman 580.752101 engine bogs down under load?
    • C
      Christopher KellySep 12, 2025
      If the engine runs well without a load but bogs down when you add a load to your Craftsman Pressure Washer, move the throttle control to the FAST position. If the engine still bogs down, contact a Sears service facility.

Craftsman 580.752101 Specifications

General IconGeneral
Weight60 lbs
Engine Displacement (cc)190 cc
Engine Displacement190 cc
Pump TypeAxial Cam
Soap TankYes
WheelsYes
Power SourceGasoline
Hose Length25 feet
Engine TypeOHV

Related product manuals