Need help?Do you have a question about the Craftsman 917.353771 and is the answer not in the manual?
General| Model Number | 917.353771 |
|---|---|
| Engine Displacement | 42cc |
| Bar Length | 18 inches |
| Chain Pitch | 0.325 inches |
| Chain Gauge | 0.050 inches |
| Type | Gasoline Chainsaw |
| Engine | 2-cycle engine |
Details the 90-day repair warranty for defects in material and workmanship.
Familiarize yourself with the saw and proper cutting methods before use.
Prohibits operation by children or untrained adults.
Ensure a safe distance for onlookers and pets during operation.
Advise carrying fire equipment and handling fuel safely.
Avoid indoor use due to carbon monoxide and start safely.
Explains kickback and how to avoid it via proper positioning.
Keep the saw clean, tight, and ensure proper adjustments.
Provides guidelines for safe transport and storage of the saw.
Step-by-step guide for attaching the hand guard.
Instructions for mounting the guide bar and chain.
Details on how to properly tension the saw chain.
Guide on filling the chain oil tank with lubricant.
Instructions for mixing fuel and filling the fuel tank.
Procedures for starting the engine, including cold and warm starts.
Simple instruction to turn off the engine using the switch.
Explains how to use the automatic and manual oiling systems.
Checklist of items to verify before starting to cut.
Provides tips for proper grip, footing, and cutting methods.
Assessing the tree's lean, branches, and wind conditions.
Identifying and clearing a safe escape path before felling.
Removing obstacles around the tree and escape route.
Step-by-step guide for making the undercut and backcut.
Actions to take as the tree falls, including moving away.
Analyzing the felling cut for technique improvement.
Techniques for cutting branches from a felled tree.
Methods for cutting logs into desired lengths.
Safe techniques for pruning limbs from standing trees.
Daily checks and general service recommendations.
Covers maintenance for the guide bar and chain.
Guidance on when and how to sharpen the saw chain.
Specific instructions for power sharpening cutter top plates.
Procedure for filing the side plates of the chain cutters.
Instructions for filing the depth gauges on chain cutters.
How to rotate the power sharpening stone for even wear.
Procedures for repairing minor damage to the guide bar.
When and how to replace the saw chain.
Guidance on replacing the chain sprocket.
Steps for cleaning the air filter to maintain engine performance.
How to adjust the carburetor for optimal engine performance.
Instructions for cleaning engine cooling fins for better airflow.
Cleaning carbon deposits from exhaust and muffler components.
Procedures for cleaning or replacing the spark plug.
Replacing worn clutch shoes and springs for proper engagement.
Step-by-step guide to replacing the starter rope.
Instructions for replacing the starter spring.
Guidance on replacing the pawl springs in the starter.
Addresses issues with the starter rope not rewinding properly.
Troubleshooting for starter pawls or springs not engaging.
Covers common causes for engine starting problems.
Solutions for a carburetor that is flooding the engine.
Diagnosing and fixing issues with the engine not idling.
Troubleshooting engine hesitation or lack of acceleration.
Addresses low power or engine stalling during cutting.
Identifying and resolving engine knocking sounds.
Solutions for engine backfiring or misfiring issues.
Troubleshooting for chain movement when the engine is at idle.
Addresses issues where the chain doesn't move when throttle is applied.
Reasons and solutions for the chain stopping mid-cut.
Diagnosing poor cutting performance or pulling.
Troubleshooting rough chain operation, chatter, or grabbing.
Identifying causes for slanted cuts and how to correct them.
Reasons for chain breakage and how to prevent it.
Troubleshooting for the chain jumping off the guide bar.
Solutions for chipped guide bar edges.
Diagnosing issues with the manual oil pump not delivering oil.
Exploded view and part numbers for the main frame assembly.
Exploded view and part numbers for cutting and sharpening components.
Exploded view and part numbers for engine, clutch, and muffler.
Exploded view and part numbers for the solid state ignition system.
Exploded view and part numbers for the recoil starter assembly.
Exploded view and part numbers for the carburetor assembly.
Exploded view and part numbers for the carburetor for specific models.
Lists available accessories and repair parts for the chain saw.
To Next Page