EasyManua.ls Logo

Craftsman S145 - User Manual

Craftsman S145
64 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
769-20650 / 00 02/19
2-CYCLE GAS CHAINSAW
MOTOSIERRA DE GAS DE 2 TIEMPOS
OPERATOR’S MANUAL | MANUAL DEL OPERADOR
S145 | S160 | S180
CMXGSAMNN4214 | CMXGSAMNN4216 | CMXGSAMCX4218
1-888-331-4569 WWW.CRAFTSMAN.COM
IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.
ORIGINAL INSTRUCTIONS | TRADUCCIÓN DE LAS INSTRUCCIONES ORIGINALES

Table of Contents

Other manuals for Craftsman S145

Preview: Operator's Manual
Operator's Manual64 pages

Questions and Answers

  • D
    Daniel GatesAug 18, 2025
    Why won't my Craftsman S145 engine start?
    • L
      lewiscarolAug 18, 2025
      Several factors can prevent your Craftsman Chainsaw engine from starting. It could be due to an empty fuel tank, which requires filling with properly-mixed fuel. If the primer bulb hasn't been pressed enough, press it 10 times or until fuel is visible. A flooded engine can also be the culprit; in this case, move the choke knob to Position 2, press the throttle lockout, squeeze the throttle control, and pull the starter rope. Old or improperly mixed fuel (over 30 days) necessitates draining the tank and adding fresh fuel. Finally, the spark plug might not be working properly, so refer to the section on maintaining the spark plug.
  • D
    Dr. Courtney SandersAug 21, 2025
    What to do if my Craftsman Chainsaw guide bar and saw chain are running hot and smoking?
    • M
      Melissa RiveraAug 21, 2025
      If the guide bar and saw chain of your Craftsman Chainsaw are running hot and smoking, several issues could be responsible. First, the saw chain tension might be too tight; in this case, adjust the saw chain tension. Also, the chain oil reservoir may be empty, so refill it. Another potential cause is dirty guide bar grooves and oil passages, which require cleaning. Lastly, the automatic oiler flow might be too low, so increase the oil flow.
  • J
    James BenderAug 23, 2025
    Why does my Craftsman Chainsaw engine lack power or stall?
    • A
      Allen OrrAug 23, 2025
      If your Craftsman Chainsaw engine lacks power or stalls, the issue might be old or improperly mixed fuel (over 30 days). In this case, drain the fuel tank and add fresh, properly-mixed fuel. A dirty air filter can also cause these problems, so clean or replace the air filter. The spark plug might not be working properly, so refer to the section on maintaining the spark plug.
  • S
    Shelby VasquezAug 26, 2025
    What to do if the saw chain on my Craftsman S145 comes off the guide bar?
    • J
      Justin SmithAug 26, 2025
      If the saw chain keeps coming off the guide bar on your Craftsman Chainsaw, it could be that the saw chain tension is too loose, so adjust it. Also, the guide bar and saw chain may be assembled incorrectly, so refer to the section on removing and installing the guide bar and saw chain.
  • M
    Misty OsborneAug 28, 2025
    Why won't my Craftsman S145 engine idle?
    • M
      Mark DorseyAug 28, 2025
      If your Craftsman Chainsaw engine won't idle, it could be due to a dirty air filter, so clean or replace it. Another cause might be old or improperly mixed fuel (over 30 days); in that case, drain the fuel tank and add fresh, properly-mixed fuel. Finally, the idle speed could be incorrect, so adjust the idle speed.
  • A
    Amanda RodriguezAug 30, 2025
    What to do if the saw chain rotates but doesn't cut on my Craftsman S145?
    • R
      ryankramerAug 30, 2025
      If the saw chain on your Craftsman Chainsaw rotates but doesn't cut, the saw chain is likely dull, so sharpen or replace it. Also, the saw chain might be on backwards, so check and correct the saw chain direction.
  • A
    angelahernandezSep 1, 2025
    What to do if my Craftsman S145 Chainsaw engine lacks power or stalls?
    • T
      Tyler BaileySep 1, 2025
      If your Craftsman Chainsaw engine lacks power or stalls, it could be due to: * Old or improperly mixed fuel: Drain the fuel tank and add fresh, properly-mixed fuel. * A dirty air filter: Clean or replace the air filter.
  • Q
    qhowardSep 3, 2025
    What to do if the Craftsman S145 Chainsaw guide bar and saw chain are running hot and smoking?
    • N
      Nichole HarrisSep 3, 2025
      If the guide bar and saw chain are running hot and smoking, consider the following: * The saw chain tension might be too tight; adjust the saw chain tension. * The chain oil reservoir could be empty; refill it. * The guide bar groove and oil passages may be dirty; clean them. * The automatic oiler flow might be too low; increase the oil flow.
  • J
    Joshua ColeSep 6, 2025
    Why Craftsman S145 Chainsaw engine will not accelerate?
    • E
      Edward DunlapSep 6, 2025
      If your Craftsman Chainsaw engine will not accelerate, the possible causes are: * The fuel is old (over 30 days) and/or improperly mixed, so drain the fuel tank and add fresh, properly-mixed fuel. * The air filter is dirty, so clean or replace the air filter.
  • H
    hernandezanthonySep 8, 2025
    What to do if my Craftsman S145 Chainsaw saw chain does not rotate?
    • L
      Lacey CarpenterSep 8, 2025
      If the saw chain on your Craftsman Chainsaw does not rotate, check the following: * The saw chain tension might be too tight; adjust it. * The chain brake may be engaged; disengage the chain brake. * Inspect the guide bar and saw chain for damage. Replace them if necessary.

Summary

Safety Information

Safety Symbols and Warnings

Explains danger, warning, caution symbols and specific warnings for user safety.

Spark Arrestor Note

Information on spark arrestor requirements for certain regions and its function.

Important Safety Instructions

General Operating Safety

Key precautions before and during operation for user and bystander safety.

Gas Unit Safety

Specific safety measures for handling fuel and preventing ignition.

Safe Operating Practices

Guidelines for using the unit correctly and safely, including protective gear.

Kickback Safety

Understanding Kickback Hazards

Explains rotational and linear kickback phenomena and their causes.

Kickback Safety Precautions

Steps to reduce kickback risk and maintain control of the chainsaw.

Additional Safety Warnings

General Safety and Maintenance Precautions

Covers additional safety tips, maintenance safety, and storage guidelines.

Safety and International Symbols

Understanding Key Symbols

Explains common safety alert and operational symbols used on the product.

Know Your Unit

Unit Components and Applications

Identifies chainsaw parts and lists typical applications like felling and pruning.

Essential Terms and Definitions

Glossary of Chainsaw Terminology

Defines key terms related to chainsaw operation, parts, and safety.

Specifications and Parts

Chainsaw Technical Specifications

Lists detailed specs like displacement, bar length, chain pitch, and weight.

Replacement Parts List

Provides part numbers and descriptions for ordering replacement items.

Assembly and Setup

Initial Setup Procedures

Covers adding bar and chain oil and testing the chain brake functionality.

Oil and Fuel Handling

Fueling the Unit Safely

Instructions for safe refueling, fuel mixture ratios, and avoiding E85 fuel.

Starting and Stopping the Chainsaw

Starting Procedures

Step-by-step guide for preparing and starting the engine.

Chainsaw Operation

Safe Operation Guidelines

Tips for best results, cutting wood types, and safety during operation.

Stopping Procedures

Instructions for normal engine shutdown and emergency stopping.

Work Area and Handling

Preparing the Work Area

Clearing the area of obstructions and ensuring safe footing.

Proper Unit Handling

Techniques for holding the chainsaw correctly to maintain control.

Felling Trees

Felling Safety Precautions

Safety measures for cutting down trees, including escape routes.

Felling Procedure Steps

Instructions for removing buttress roots and making the undercut.

Advanced Felling and Limbing

Making the Felling Back Cut

Steps for the final cut to fell a tree and using wedges.

Limbing a Fallen Tree

Procedures for safely removing branches from a felled tree.

Bucking Logs

Bucking Safety Precautions

Safety precautions for cutting logs into desired lengths.

Cutting Logs Under Stress

Techniques for cutting bent logs and preventing chain pinching.

Pruning and Cutting Techniques

Overbucking and Underbucking

Cutting techniques for logs and branches, including handling forces.

Pruning a Living Tree

Steps for safely removing limbs from a living tree.

Maintenance Schedule

Routine Maintenance Checklist

Outlines required maintenance procedures based on usage frequency.

Bar and Chain Lubrication

Adding Bar and Chain Oil

Instructions for filling the chain oil reservoir and maintaining oil level.

Adjusting Oil Flow

How to adjust the automatic oiler for proper chain lubrication.

Chain Tension Adjustment

Adjusting Chain Tension

Procedure for setting proper chain tension for optimal performance.

Guide Bar and Saw Chain

Installing the Guide Bar and Saw Chain

Step-by-step guide for correctly assembling the guide bar and chain.

Maintaining the Saw Chain

Tips for keeping the chain sharp and in good condition.

Sharpening the Saw Chain

Chain Filing Techniques

Detailed instructions for sharpening chain cutters using files.

Guide Bar Maintenance

Cleaning and Lubricating Guide Bar

Procedures for cleaning the guide bar groove and lubricating the sprocket tip.

Air Filter and Chain Replacement

Cleaning the Air Filter

Steps for cleaning the air filter to maintain engine performance.

Replacing Guide Bar and Saw Chain

Instructions for replacing the guide bar and using low-kickback chains.

Engine Adjustments and Spark Plug

Adjusting Idle Speed

How to adjust the engine idle speed for proper operation.

Maintaining the Spark Plug

Procedure for inspecting, gapping, and replacing the spark plug.

Cleaning and Storage

Unit Cleaning Procedures

Instructions for cleaning the chainsaw after use and for storage.

Storing the Chainsaw

Guidelines for storing the unit, including long-term storage.

Troubleshooting

Common Problems and Solutions

Guides users through diagnosing and fixing common engine and chain issues.

Limited Warranty

Warranty Coverage and Exclusions

Details what the limited warranty covers and lists common exclusions.

Warranty Limitations

Warranty Limitations and Disclaimers

Explains limitations on implied warranties and disclaimers of liability.

Craftsman S145 Specifications

General IconGeneral
Bar Length14 inches
Weight13.2 lbs
Chain Pitch3/8 in
Fuel Capacity16.9 fl oz
Oil Capacity6.8 oz
Engine Displacement42 cc
Engine Type2-cycle
Chain Gauge0.050 inches

Related product manuals