Craftsman 919.195410 - User Manual

Questions and Answers

S
Stephen RoyAug 20, 2025
Why is my Craftsman 919.195410 not supplying enough air?
- P
  Peter EvansAug 20, 2025
  If the Craftsman Air Compressor is not supplying enough air, it could be due to prolonged excessive use, or the compressor might not be large enough for the air requirement. Other causes may include a hole in the hose, a restricted check valve, air leaks, a restricted air intake filter, or a loose belt. To resolve this, decrease the amount of air usage and check the accessory's air requirement. If it exceeds the SCFM or pressure supplied by your air compressor, consider using a larger compressor.
J
johnsonsandraAug 22, 2025
Why will my Craftsman 919.195410 motor not run?
- J
  julieshermanAug 22, 2025
  If the motor of your Craftsman Air Compressor will not run, it could be due to several reasons: the motor overload protection switch might have tripped, the tank pressure might exceed the pressure switch “cut-in” pressure, the check valve could be stuck open, there might be loose electrical connections, the motor or starting capacitor could be defective, paint spray may be on internal motor parts, the pressure release valve on the pressure switch might not have unloaded head pressure, or a fuse could be blown, or the circuit breaker tripped. Allow the motor to cool off.
R
Rickey MartinezAug 25, 2025
How to fix air leaks at fittings on Craftsman 919.195410 Air Compressor?
- M
  Michael MartinAug 25, 2025
  If you notice air leaks at the fittings of your Craftsman Air Compressor, it's likely that the tube fittings aren't tight enough. Tighten the fittings where you hear air escaping, and you can use a soapy water solution to help identify leaks. Be careful not to overtighten them.
C
Cheryl KingAug 26, 2025
What to do if Craftsman 919.195410 Air Compressor has air leak from safety valve?
- K
  kevin46Aug 27, 2025
  If the safety valve on your Craftsman Air Compressor is leaking air, it might be due to a defect in the safety valve. Try manually operating the safety valve by pulling on the ring. If the valve continues to leak after doing this, it should be replaced.
A
Angelica EllisAug 28, 2025
What to do if Craftsman 919.195410 regulator will not shut off air outlet?
- J
  jasmineturnerAug 28, 2025
  If the Craftsman Air Compressor regulator will not shut off the air outlet, it is likely due to a damaged regulator, which will need to be replaced.
S
Shannon DavisAug 30, 2025
Why does the safety valve pop off on my Craftsman 919.195410 Air Compressor?
- J
  Jesse ClayAug 30, 2025
  If the safety valve on your Craftsman Air Compressor pops off due to excessive tank pressure, it may be because the pressure switch isn't shutting off the motor when the compressor reaches the “cut-out” pressure, or the pressure switch “cut-out” is set too high. Move the On/Auto/Off lever to the “OFF” position, and if the air compressor does not shut off, contact a Trained Service Technician.
M
Mark BensonAug 31, 2025
What to do if Craftsman 919.195410 has air leaks in the tank?
- T
  Thomas JohnstonAug 31, 2025
  If you suspect air leaks in the air tank or at the air tank welds of your Craftsman Air Compressor, it indicates a defective air tank that must be replaced. Do not attempt to repair the leak, drill into, weld, or modify the air tank, as this can weaken it and cause it to rupture or explode.
J
John PalmerSep 2, 2025
How to fix air leaks at check valve in Craftsman Air Compressor?
- P
  pwolfSep 3, 2025
  If there's an air leak at or inside the check valve of your Craftsman Air Compressor, it's likely that the check valve seat is damaged. A defective check valve results in a constant air leak at the pressure release valve when there is pressure in the tank and the compressor is shut off. Replace the check valve.
T
Tyler ChanSep 4, 2025
What to do if Craftsman 919.195410 has air leaks between head and valve plate?
- W
  William ValenciaSep 4, 2025
  If there are air leaks between the head and valve plate of your Craftsman Air Compressor, it indicates a leaking seal. Contact a Trained Service Technician.
B
Barbara HayesSep 6, 2025
What to do if Craftsman 919.195410 Air Compressor has air leaks at pressure switch release valve?
- J
  jwilliamsSep 6, 2025
  If you notice air leaks at the pressure switch release valve (if equipped) on your Craftsman Air Compressor, it indicates a defective pressure switch release valve. Contact a Trained Service Technician.