EasyManua.ls Logo

Craftsman 944.364290 - User Manual

Craftsman 944.364290
25 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Revision 1:
Page 3 – updated Safety Rules to latest ANSI specs.
Page 4 – updated API Oil Classification to SG-SL in Product Specifications.
Page 7 – added “18 oz. Oil note” to Add Oil section.
Page 11 – updated API Oil Classification to SG-SL in Lubrication.
Page 16 – updated art to new “standard” Adobe Illustrator version, changing virtually
every Key number in the process (#1, #24 and #35 remain unchanged).
Here’s the list: Key #2 to 8, #3 to 2, #5 to 19, #7 to 59, #8 to 5, #9 to 57,
#10 to 6, #12 to 58, #18 to 12, #19 to 10, #22 to 20, #23 to 56, #25 to 33,
#27 to 45, #28 to 36, #29 to 42, #30 to 61, #36 to 34, #38 to 32, #39 to 31,
#40 to 30, #41 to 29, #42 to 28, #43 to 27, #45 to 25, #46 to 52, #48 to 14,
#49 to 43, #51 to 62, #52 to 41, #53 to 50, #54 to 49, #55 to 48, #56 to 47,
#57 to 46, #58 to 38, #62 to 44, #63 to 23, #64 to 22, #68 to 64, #69 to 11,
#70 to 9, #71 to 18 and #72 to 13. Whew!
Page 17 – changed Key numbers as listed above.
Page 18 – updated art to new “standard” Adobe Illustrator version, changing Key #3 to 7,
#26 to 3 and #37 to 40 in the process. Changed #7 to 191730.

Table of Contents

Questions and Answers

  • J
    jenniferdavisAug 14, 2025
    Why won't my Craftsman Lawn Mower start?
    • S
      scott82Aug 14, 2025
      Your Craftsman Lawn Mower might not start due to several reasons. It could be a dirty air filter (clean or replace it), lack of fuel (fill the fuel tank), stale or water-contaminated fuel (empty and refill with fresh gasoline), a disconnected spark plug wire (connect it), a bad spark plug (replace it), a loose or broken blade adapter (tighten the blade bolt or replace the adapter), or the control bar not being depressed (depress it to the handle). Also check if the fuel valve lever is in the OFF position and turn it to ON.
  • R
    richardtaylorAug 17, 2025
    What causes an uneven cut with my Craftsman Lawn Mower?
    • J
      Jacqueline DoyleAug 17, 2025
      An uneven cut with your Craftsman Lawn Mower can be caused by a worn, bent, or loose blade (replace the blade and tighten the blade bolt), uneven wheel heights (set all wheels at the same height), or a buildup of grass under the mower (clean the underside of the mower housing).
  • A
    Amanda AdamsAug 21, 2025
    What if my Craftsman Lawn Mower still doesn't start after basic checks?
    • B
      Beth MartinAug 21, 2025
      If your Craftsman Lawn Mower still doesn't start after checking the basics, the control bar might be defective (replace it). Also, check if the fuel valve lever (if equipped) is in the OFF position and turn it to the ON position. If your mower has a battery, it might be weak (charge the battery) or disconnected (connect the battery to the engine).
  • T
    Tony HudsonAug 25, 2025
    What to do if my Craftsman 944.364290 Lawn Mower loses power?
    • A
      ashley35Aug 25, 2025
      If your Craftsman Lawn Mower is losing power, it could be due to several factors: the mower housing or blade dragging in the grass (raise the cutting height), cutting too much grass at once (raise the cutting height), a dirty air filter (clean or replace it), a buildup of grass under the mower (clean the underside of the mower housing), too much oil in the engine (check the oil level), or walking too fast (cut at a slower walking speed).
  • B
    Brenda WilliamsAug 27, 2025
    How to fix a Craftsman Lawn Mower that vibrates excessively?
    • M
      mwilliamsonAug 27, 2025
      Excessive vibration in your Craftsman Lawn Mower can be caused by a worn, bent, or loose blade (replace the blade and tighten the blade bolt). If that doesn't solve the issue, the engine crankshaft might be bent, in which case you should contact a qualified service center.
  • K
    Karen TaylorAug 30, 2025
    Why is my Craftsman 944.364290 Lawn Mower hard to push?
    • M
      Mark LeeAug 30, 2025
      If your Craftsman Lawn Mower is hard to push, the grass might be too high, or the wheel height is too low (raise the cutting height). Another reason could be the rear of the mower housing or blade dragging in grass (raise the rear of the mower housing one setting higher). Also, check if the grass catcher is too full (empty it) or if the handle height isn't right for you (adjust the handle height).
  • P
    pkaiserSep 3, 2025
    Why is the starter rope hard to pull on my Craftsman 944.364290?
    • P
      peggy23Sep 3, 2025
      If the starter rope on your Craftsman Lawn Mower is hard to pull, it could be because the engine flywheel brake is engaged when the control bar is released (depress the control bar to the upper handle before pulling the starter rope). Another potential cause is a broken blade adapter (replace the blade adapter) or the blade dragging in grass (move the lawn mower to cut grass or to a hard surface).
  • J
    Julia PrinceSep 6, 2025
    Why isn't my Craftsman 944.364290 grass catcher filling up?
    • M
      mariafloresSep 6, 2025
      If the grass catcher on your Craftsman Lawn Mower isn't filling up, it could be due to the cutting height being too low (raise the cutting height), the lift on the blade being worn off (replace the blade), or the catcher not venting air (clean the grass catcher).
  • R
    Rodney EdwardsSep 10, 2025
    What to do if my Craftsman Lawn Mower drive speed is slowing?
    • J
      joshuaochoaSep 10, 2025
      If your Craftsman Lawn Mower experiences a loss of drive or slowing of drive speed, check the drive belt for wear and replace if necessary. Also, check if the belt is off the pulley and reinstall it if needed. Finally, inspect the drive cable for wear or breakage and replace it if required.

Craftsman 944.364290 Specifications

General IconGeneral
Engine BrandBriggs & Stratton
Cutting Height Positions6
Deck MaterialSteel
Starter TypeRecoil
Engine Type4-Cycle
Cutting Width21 inches
Cutting Height Range1.25-3.75 inches
Warranty2 years limited
Starting SystemRecoil

Related product manuals