Craftsman CMPCS38 User Manual

7
ENGLISH

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.
Three Year Limited Warranty
CRAFTSMAN will repair or replace, without charge, any
defects due to faulty materials or workmanship for three
years from the date of purchase. This warranty does
not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty
repair information, visit www.craftsman.com or call
1-888-331-4569. This warranty does not apply to
accessories or damage caused where repairs have been
made or attempted by others. THIS LIMITED WARRANTY
IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states orprovinces.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your CRAFTSMAN Power Tool or Nailer for any reason, you
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questionsasked.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-888-331-4569
for a freereplacement.
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
ofpurchase.
• FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
SafetyAct.
Register online at www.craftsman.com/registration
IMPORTANT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwallsystem.
1. Remove air supply and accessories.

CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
theVersatrack™ Trackwall.
2. Attach the hang hook
8
on the tool.
a. Use a wrench to remove the fitting
4
.
b. Place the Versatrack™ hang hook on the fitting.
c. Use a wrench to re-install the fitting at the base of
the tool.
NOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Fig. G
4
8
Versatrack Variables
1ST_Figure 1ST_Callout 2ND_Callout
G 8 4
Belt Hook

WARNING: Always disconnect tool from air supply
when making adjustments or servicing.

WARNING: The operator must not hold the secondary
trigger pulled except during fastening operation as
serious injury could result if the trigger accidentally
contacts someone or something, causing the tool
to cycle.

WARNING: Never inadvertently pull or grasp the
secondary trigger when moving about, changing
work location, when holstering or hanging tool, or
when preparing work surface for fastening operation.
1. Use a wrench to remove the fitting.
2. Place the belt hook on the fitting.
If the belt hook is not desired at all, it can be removed from
thetool.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performingthis.

Craftsman CMPCS38 Specifications

General

Brand	Craftsman
Model	CMPCS38
Category	Tools
Language	English