Craftsman CMXGMAM823762

To Next Page

WARNING!

Before using this equipment, read the manual and follow all safety rules and operating instructions. SAVE THESE INSTRUCTIONS.

Form No. 769-19131

(November 26, 2018)

INSTRUCTION MANUAL | GUIDE D’UTILISATION

FRONT WHEEL DRIVE MOWER

Model Nos. CMXGMAM823762

CMXGMAM823761

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

1-888-331-4569 WWW.CRAFTSMAN.COM

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all models and the model depicted may differ

from yours.

TABLE OF CONTENTS

Safety Instructions ............................................... Pages 2-5

Slope Guide ..........................................................Page 6

Unpacking ...........................................................Page 7

Assembly .........................................................Pages 7-9

Adjustments ........................................................Page 10

Operation .......................................................Pages 11-14

Service and Maintenance ........................................Pages 15-17

Off-Season Storage ..................................................Page 18

Troubleshooting ................................................. Page 19-20

French ...........................................................Page 21

Need help?

Do you have a question about the Craftsman CMXGMAM823762 and is the answer not in the manual?

This document is an instruction manual for a Craftsman Front Wheel Drive Mower, specifically models CMXGMAM823762 and CMXGMAM823761. It provides comprehensive information on safety, assembly, operation, maintenance, and troubleshooting.

Function Description:

The Craftsman Front Wheel Drive Mower is designed primarily for mowing grass. It features a rotating blade that cuts grass, and depending on the model, can be configured for mulching, side discharge, or bagging clippings using a grass catcher. The front-wheel-drive mechanism (if equipped) assists in propelling the mower, reducing operator effort. A blade control handle acts as a safety device, stopping the engine and blade when released.

Important Technical Specifications:

While specific engine details (like horsepower or displacement) are not provided in this manual, it emphasizes that the unit is shipped without gasoline or oil and requires servicing with both before first use. The mower is designed for operation on regular unleaded gasoline. It includes emission control systems (Engine Modification, Oxidizing Catalyst, Secondary Air Injection, and Three Way Catalyst, if equipped) to comply with California and federal EPA regulations for Small Off Road Equipment. The maximum safe operating speed of the engine is controlled by a governor, which should not be tampered with. The manual also states that the cutting blade stops rotating within three seconds of releasing the blade control handle. The maximum recommended slope for operation is 15 degrees. The average useful life of the product is seven years or 140 hours of operation, as per CPSC and EPA.

Usage Features:

Cutting Height Adjustment: The mower features a cutting height adjustment lever located above the front and rear right wheel. All wheels must be set to the same position for a uniform cut. For rough or uneven lawns, a higher position is recommended to prevent cutting the grass too close.
Drive Control (If Equipped): Models may come with a bail or single lever drive control, or a dual lever system. Squeezing the control(s) against the upper handle engages the drive, while releasing it slows down or stops the mower. An adjustment wheel in the drive control handle housing allows for tightening or loosening the drive belt, which may be necessary if the mower does not propel itself or hesitates.
Mulching: The mower is shipped as a mulcher. For effective mulching, the grass catcher or side discharge chute should be removed, and the rear mulch plug (if equipped) should be installed. Mulching is not recommended for wet grass or grass exceeding four inches in height.
Side Discharge (If Equipped): To convert to side discharge, the mulch cover is lifted, and two hooks of the side discharge cover are slid under the hinge pin of the mulching cover assembly. The side mulching cover should not be removed, even when not mulching.
Grass Catcher (If Equipped): The grass catcher, located at the rear, collects clippings. It is attached by lifting the rear discharge door and placing the catcher into slots in the handle brackets.
Recoil Starter: The recoil starter handle is located on the right upper handle. The operator stands behind the unit and pulls the rope to start.
Deck Wash (If Equipped): Some models include a water port on the deck surface for a deck wash system, used to rinse grass clippings from the underside of the deck. This is recommended after each mowing.
Handle Pitch Adjustment (If Equipped): The handle pitch can be adjusted to one of three positions for operator comfort by removing and reattaching wing nuts and carriage bolts.

Maintenance Features:

The manual provides a detailed maintenance schedule covering "Each Use," "1st Month or 5 hours," "Annually or 25 hours," "Annually or 50 hours," "Annually," and "Before Storage."

Engine Maintenance: This includes checking engine oil level, cleaning the air cleaner, and changing engine oil. The manual advises against using water to clean engine parts to prevent fuel system contamination.
Mower Maintenance:
- Cleaning Deck: The underside of the mower deck should be cleaned once a season to prevent debris buildup. This involves running the engine until it's out of fuel, disconnecting the spark plug wire, tipping the mower (muffler side down), and scraping the underside.
- Deck Wash: For models with a deck wash system, it involves attaching a garden hose to the water port, turning on the water, starting the engine for at least two minutes to rinse the deck, then stopping the engine, turning off water, and detaching the hose. The engine should then be restarted for two minutes to dry the deck.
- Blade Care: The blade and engine mounting bolts should be checked for tightness regularly. The blade should be inspected for damage (bent, cracked, worn) and replaced with original equipment manufacturer's (O.E.M.) parts only. When servicing the blade, safety gloves or a heavy rag should be used. The blade adapter should also be checked and replaced if damaged. The blade's balance should be checked, and the heavier side sharpened to ensure proper balance. The blade bolt should be tightened to 450-600 in-lb (50-67 Nm).
- Lubrication: Pivot points on the blade control should be lubricated with light oil at least once a season.
- Fuel System: Before storage, the fuel system should be prepared by running the engine until it stops from lack of fuel or by adding a gasoline additive and running the engine for several minutes to circulate it.
- Battery (If Equipped): The battery must be fully charged before storage and recharged monthly for optimal life. The electric start push key should be removed and stored safely.
General Recommendations: Always observe safety rules, check all adjustments at least once per season, and periodically check all fasteners for tightness. The warranty may be voided if the engine governor speed is modified. The manual also advises against storing the mower with fuel in poorly ventilated areas due to fire hazards.