Page 14 of 29
Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “Config
1 0”. Press key number 2 to scroll to the next configuration code. Press key number 1 to return to “Config
Switches”. Press key number 2 will scroll to next routine.
*”Correct Change” - CORRECT CHANGE ONLY CONTROL ROUTINE
This function is used to allow consumer overpay, set a correct change value, and set an unconditional acceptance value.
Press key number 4 will enter “ConsumerOverpay#”.
“ConsumerOverpay #” - Allow Consumer Overpay
This function allows the vender to vend with the risk of not being able to return the full amount of change. This
function has to be turned on to be able to allow consumer overpay. Press key number 4 and display will show
“ConsumerOverpay #”, where “#” is flashing. “ConsumerOverpay1” will allow consumer overpay (customer
could potentially be shortchanged) and “ConsumerOverpay0” will not allow consumer overpay (will not allow
customer to be shortchanged). Press key number 2 or 3 to scroll between ” ConsumerOverpay0” and
“ConsumerOverpay1”. Press key number 4 with the display blinking the setting you wish to use. Display will
return to “ConsumerOverpay#”.
Press key number 2 to scroll to “Corr Chg value”.
“Corr Chg Value” - Correct Change Value
This is the function that the control board will use to set a value which will turn on the correct change
indicator. Note: If “Uncond Accept” is set, the “Corr Chg Value” should be equal to or less than the “Uncond
Accept”. Note: If the value set is 00.00, the correct change indicator will never come on.
If the controller determines that it cannot return the exact amount of the correct change value or any value less
than it, then the indicator will be turned on. Press key number 4 and the display will show “##.##’. Press key
number 2 or 3 to scroll from 00.00 to 99.99. Press key number 4 with the display showing the value you wish to
use. Display will return to “Corr Chg Value”. Press key number 2 to scroll to “Uncond Accept”.
“Uncond Accept” - Unconditional Acceptance Value
This is the function that the control board will use to set the largest value of any single form or currency (coin or
bill) that can be accepted without having enough change to pay back the full amount. Press key number 4 and
the display will show “##.##”. Press key number 2 or 3 to scroll from 00.00 to 99.95. Press key number 4 with
the display showing the value you wish to use. Display will return to “Uncond Accept”. Press key number 1 to
return to “CorrectChange”. Press key number 2 to scroll to next routine.
*”Preview Password” - PREVIEW DATA PASSWORD ROUTINE
This function is used to enable viewing of cash collected, product sales, and error codes without opening the door. To
view the data the 4 digit password (4-2-3-1) must be entered. Once entered the “Cash Counters”, “Sales Counters”,
“Error Codes”, and “Return to Sales” menus are available from the front of the vender. To view, follow instructions for
cash counter routine, sales counter routines, error routine and return.
To change “Preview Password” password:
At “Preview Password” press key number 4, “####” (representing current four digit password) will show on display with
the far left digit blinking. Press key number 2 to scroll to number desired for password. Press key number 4. The next
digit will start blinking, press key number 2 to scroll to number desired for password. Press key number 4. Continue this
process until all 4 digits are set. Then press key number 4 and the display will return to “Preview Password” and the new
password has been saved. Pressing key number 1 at any time during this routine will return to “Preview Password” with
no changes to password occurring. Press key number 2 to scroll to next routine.
To Next Page
Loading...
Need help?
General
