Crestron DMPS3-4K-150-C Do Guide

DO GUIDE
DMPS3-4K-150 -C
3-Series
®
4K DigitalMedia
TM
Presentation System 150
DO Install the Device
The DMPS3-4K-150-C can be mounted into a rack, mounted under a table,
or placed onto a  at surface.
Mounting into a Rack
The DMPS3-4K-150-C occupies 1U of rack space. Using a #1 or #2 Phillips
screwdriver, attach the two included rack ears to the device. Then, mount
the device into the rack using four mounting screws (not included).
Mounting under a Table
Using a #1 or #2 Phillips screwdriver, attach the four included table mount
brackets to the device. Then, attach the four table mount brackets to the
underside of the table using four mounting screws (not included).
Placing onto a Flat Surface
When placing the device onto a  at surface or stacking it with other
equipment, attach the included feet near the corners on the underside of
the device.
DO Make Connections to the Rear Panel
Make connections to the rear panel of the DMPS3-4K-150-C as follows:
VGA IN 1–4: Connect to RGB (VGA), component, S-video, or composite
video sources.
AUDIO IN 1–4: Connect to unbalanced audio sources.
HDMI IN 1–4: Connect to HDMI
®
audio/video sources.
DM IN 1–2: Connect to the DM 8G+™ output of DigitalMedia™
transmitters or other DigitalMedia devices or to third-party HDBaseT
®
devices.
1
HDMI OUT: Connect to the display.
DM OUT: Connect to the DM 8G+ input of a DigitalMedia receiver or other
DigitalMedia device or to a third-party HDBaseT device.
1
RELAY 1–2: Connect to controllable devices.
INPUT: Connect to a digital or analog output device.
AUDIO OUT: Connect to the receiving device using the supplied 5-pin
interface connector.
IR OUT: Connect to the included Crestron
®
STIRP IR emitter probe.
MIC IN: Connect to a microphone.
COM: Connect to the device to be controlled using the included 5-pin
interface connector.
LAN: Connect to the local area network.
USB 1–4 (Type A): Connect to the USB port of TT-100 Series presentation
interfaces.
G: Connect to earth ground (building steel).
NET: Connect to the 4-pin NET port of a Cresnet
®
device using the
included 4-pin interface connector.
100–240V~1.4A 50/60 Hz: Connect to a 120 V power outlet using the
included power cord.
DO Check the Box
QUANTITY PRODUCT PART NUMBER
2 Bracket, Rack Ear, 1U 2032122
4 Bracket, Under Table Mount 2041951
2 Connector, 3-Pin 2003575
2 Connector, 4-Pin 2003576
2 Connector, 5-Pin 2003577
1 Emitter Probe, IR, Crestron STIRP 2001137
4 Foot, 0.5" x 0.5" x 0.23", Adhesive 2002389
1 Power Cord, 6' 7" (2 m) 2001134
Not Included: Cables, Rack Mount Screws, and Table Mount Screws
DM-RMC-4K-100-C
COM
HDMI OUT
GND
TX
RX
RTS
CTS
S
G
S
S
1
2
IR
LAN
DM IN
RESET
SETUP
24 V
0.75A MAX
DM-RMC-100-C
DM ROOM CONTROLLER
PROJECTOR
STEREO
SPEAKERS
LAPTOP
MONITOR
TT-100
TT-100
AMPLIFIER
DM-TX-201-C
USB HID HDMI RGB AUDIO SETUP
DM - TX - 20 1 - C
DM CO M PU T E R C E NT E R
RESET
IN
LAN DM OUT
HDMI OUT
PWR
24 VDC
0.75A
COMPUTER
LAPTOP
MICROPHONE
PROJECTION
SCREEN
LAN
2
3
4
TT-100

Crestron DMPS3-4K-150-C Specifications

General

Brand	Crestron
Model	DMPS3-4K-150-C
Category	Projector Accessories
Language	English