Crown Com-Tech CT-1600 - Amplifier Controls and Adjustments

Com-Tech 1600 Amplifier Service Manual
25
Q42889-8 Output Module (P10315-3 board) Parts List
Capacitors
C01 C 8511-5 .047µF 250V Ax
C02 C 8426-6 .1µF
C03 C 8426-6 .1µF
C04 C 6806-1 .01µF
C05 C 6806-1 .01µF
C06 C 6806-1 .01µF
C07 C 6807-9 .001µF
C08 C 6809-5 220pF
C09 C 6810-3 180pF
Diodes
D01 C 2851-1 1N4004
D02 C 2851-1 1N4004
D03 C 2851-1 1N4004
D04 C 2851-1 1N4004
D05 C 2851-1 1N4004
D06 C 2851-1 1N4004
D07 C 2851-1 1N4004
D08 C 2851-1 1N4004
D09 C 2851-1 1N4004
D10 C 2851-1 1N4004
D11 C 2851-1 1N4004
D12 C 2851-1 1N4004
Inductors
L00 C 6592-6 1.3µH Output Coil
L01 C 3510-2 470µH
L02 C 3510-2 470µH
Transistors
Q17 C 8508-1 NPN 2SC3298B
Q19 C 8509-9 PNP 2SA1306B
Note:Note:
Note:Note:
Note: Q18, S100, Driver Transistors, and Output
Transistors are not included with Output Module. See
Output Assembly parts list for part numbers.
Resistors
R00 C 2626-7 470
R01 C 2872-7 100
R02 C 7778-1 5.6 .5W Flame Proof
R03 C 6486-2 .2 5W
R04 C 6486-2 .2 5W
R05 C 6486-2 .2 5W
R06 C 6486-2 .2 5W
R07 C 6486-2 .2 5W
R08 C 6486-2 .2 5W
R09 C 7779-9 22 Flame proof
R10 C 2872-7 100
R11 C 7317-8 2.7 5W
R12 C 1001-4 2.7 1W
R13 C 2626-7 470
R15 C 6486-2 .2 5W
R16 C 6486-2 .2 5W
R17 C 6486-2 .2 5W
R18 C 6486-2 .2 5W
R19 C 6486-2 .2 5W
R20 C 6486-2 .2 5W
R21 C 7778-1 5.6 .5W Flame Proof
R22 C 7779-9 22 Flame Proof
R23 C 6844-2 250 Pot LS Bias
R24 C 4300-7 13K
R25 C 2628-3 2.2K
R26 C 6844-2 250 Pot HS Bias
R27 C 6495-3 390
R28 C 4300-7 13K
R30* C 6626-3* 102*
Misc.
Board P10315-3
Jumpers C 5868-2 0 Ohm .25W
Clips D 6414-3 Q17/Q19 Hold Down
J500 J600 C 7057-0 10 Pin Header
*Note: R30 is 102 Ohms in most units, though in some
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).