Need help?Do you have a question about the Crunch Blackmaxx MXB-480 and is the answer not in the manual?
Instructions on how to physically mount the amplifier using screws and considerations for placement.
Properly connecting the amplifier's ground wire to the vehicle chassis for safety and optimal performance.
Connecting the remote turn-on wire for amplifier activation with the head unit's signal.
Ensuring fused connection of the +12V power supply wire to the battery terminal for safe operation.
Information about the integrated amplifier fuses protecting against short circuits and overload conditions.
Switch to select full range, low pass, or high pass output for the internal power amplifier.
Adjustable high-pass and low-pass filter controls for frequency tuning from 40Hz to 1.2KHz.
Control to match amplifier input sensitivity to the source unit's output level (0.2V to 4V).
Control to adjust the bass boost level from 0dB up to 12dB for enhanced low frequencies.
Indicator LEDs showing amplifier power status and fault conditions like overload or heat.
Supports both line-level RCA inputs and speaker-level HI INPUT from head units.
Provides a full-range line-level RCA output for connecting additional amplifiers.
Adjustable high-pass and low-pass filter controls for frequency tuning from 40Hz to 1.2KHz.
Switch to select between 2-channel or 4-channel operation modes for flexible configurations.
Control to match amplifier input sensitivity to the source unit's output level (0.2V to 4V).
Accepts speaker-level inputs from head units that do not have line-level RCA outputs.
Indicator LED showing when the amplifier has a turn-on signal.
Control to adjust the bass boost level from 0dB up to 12dB for enhanced low frequencies.
Switch to select full range, low pass, or high pass output for the internal power amplifier.
Indicator LED for fault conditions like overload, heat, or short circuits.
Accepts line-level (RCA) inputs with a voltage range of 0.2 to 4 Volts.
Provides a full-range line-level RCA output for connecting additional amplifiers.
Connecting the amplifier for stereo speaker output, including cable checklist and cautions.
Adjusting filter, input level, and bass boost controls for stereo mode operation.
Connecting the amplifier for mono subwoofer output, including cable checklist and cautions.
Adjusting filter, input level, and bass boost controls for mono subwoofer mode.
Connecting the 4-channel amp for front/rear speakers, including cable checklist and cautions.
Adjusting filter, input level, bass boost, and input select for front/rear speaker setup.
Connecting the 4-channel amp for dual subwoofers in mono mode, with cable checklist and cautions.
Adjusting filter, input level, bass boost, and input select for dual subwoofer mono mode.
Connecting the 4-channel amp in 3-channel mode (stereo front, mono sub), with cable checklist and cautions.
Adjusting filter, input level, bass boost, and input select for 3-channel mode operation.
Connecting a 4-channel amp for stereo (front/rear) and a 2-channel amp for mono subwoofer.
Configuring controls for both the 4-channel (stereo) and 2-channel (mono) amplifiers.
Detailed power output specifications (RMS/Max) at different impedances and bridged modes.
Specifications for frequency response, damping factor, signal-to-noise ratio, and channel separation.
Details on filter types, crossover frequencies, and bass boost capabilities for all channels.
Specifications for input gain, impedance, high-level inputs, and fuse ratings.
Heatsink size dimensions (Width x Height) and overall length for mounting considerations.
General| Channels | 4 |
|---|---|
| RMS Power at 4 Ohms | 80W x 4 |
| RMS Power at 2 Ohms | 120W x 4 |
| Bridged RMS Power at 4 Ohms | 240W x 2 |
| Total RMS Power | 480W |
| Signal to Noise Ratio | >90 dB |
| THD at RMS Output | <0.05% |
| Bridgeable | Yes |
| Input Sensitivity | 200mV - 6V |
| Frequency Response | 10Hz - 30kHz |
| Power Output | 480 Watts |
| Bass Boost | 0 to +12dB |
To Next Page