Need help?Do you have a question about the CTEK Z45 Series and is the answer not in the manual?
Lists the Z45x series models (Z4500XXX, Z4550XXX, Z44009XX).
Details factory default settings for configuration parameters like IP address and admin credentials.
Explains how to access and use the web UI for configuration via Ethernet or WAN.
Describes the 2 digital output configuration and rating for 250mA at 24Vdc.
Explains the wake-up signal function for bringing the device out of low power state.
Details the 4 configurable inputs and their modes (digital, pulse, analog).
Specifies the required DC power input range of 9-24VDC with reverse polarity protection.
Details the RS-485 and RS-232 serial interfaces and their pin configurations.
Explains the functions of the reset switch for reboot and default switch for factory reset.
Describes the LAN and Service LED indicators for network and status monitoring.
Describes the Link LED states for data connection and service status.
Lists requirements before activating wireless network, including SIM card and data account.
Step-by-step guide for inserting SIM, powering up, and connecting to the network.
Instructions for installing specific radio firmware for network compatibility.
Guides on selecting APNs and provisioning wireless accounts for CDMA and GSM carriers.
Specific provisioning steps for legacy CDMA carriers using over-the-air mechanisms.
Specific provisioning steps for legacy GSM carriers requiring manual APN entry.
Explains managing user accounts, including default credentials and admin privileges.
Covers general configuration, web administration, and IP white list settings.
Configures web administration, IP white lists, and SSH access for network security.
Manages general settings, SMS access, and firewall status for system security.
Covers failed login attempts, intrusion detection, and command-line utilities for security monitoring.
Configures the LAN for gateway or client operation modes.
Details Gateway mode operations, cellular connection, and Network Address Translation (NAT).
Details Client mode operations for Ethernet connection to enterprise or home networks.
Configures location, alarming, logging, email, and dashboard display settings for applications.
Routes WAN IP traffic arriving on a specific port to a designated LAN side address.
Configures the physical electrical and timing characteristics of the serial ports.
Configures the serial (TCP/UDP/PPP) pad function for serial port options.
Allows configuration of up to 2 GRE tunnels over the cellular wireless interface.
Supports 8 concurrent IPsec tunnels with configuration options for secure communication.
Configures tunnel selection and security level globally for IPsec tunnels.
Defines tunnel-specific parameters for Phase 1 and Phase 2 of IPsec key exchange.
Synchronizes time using cellular network, NTP server, or GPS/GLONASS data.
Sets location source from built-in GPS/GLONASS receiver or user-defined coordinates.
Configures Dynamic Domain Name Service (DDNS) and cloud-based access/management system.
Mechanism to load over-the-air firmware updates and enable additional applications.
Manages backup and restore operations for system data via a USB stick.
Information on the standard Automation-Light application and licensing.
Lists the Z45x series models (Z4500XXX, Z4550XXX, Z44009XX).
Details factory default settings for configuration parameters like IP address and admin credentials.
Explains how to access and use the web UI for configuration via Ethernet or WAN.
Describes the 2 digital output configuration and rating for 250mA at 24Vdc.
Explains the wake-up signal function for bringing the device out of low power state.
Details the 4 configurable inputs and their modes (digital, pulse, analog).
Specifies the required DC power input range of 9-24VDC with reverse polarity protection.
Details the RS-485 and RS-232 serial interfaces and their pin configurations.
Explains the functions of the reset switch for reboot and default switch for factory reset.
Describes the LAN and Service LED indicators for network and status monitoring.
Describes the Link LED states for data connection and service status.
Lists requirements before activating wireless network, including SIM card and data account.
Step-by-step guide for inserting SIM, powering up, and connecting to the network.
Instructions for installing specific radio firmware for network compatibility.
Guides on selecting APNs and provisioning wireless accounts for CDMA and GSM carriers.
Specific provisioning steps for legacy CDMA carriers using over-the-air mechanisms.
Specific provisioning steps for legacy GSM carriers requiring manual APN entry.
Explains managing user accounts, including default credentials and admin privileges.
Covers general configuration, web administration, and IP white list settings.
Configures web administration, IP white lists, and SSH access for network security.
Manages general settings, SMS access, and firewall status for system security.
Covers failed login attempts, intrusion detection, and command-line utilities for security monitoring.
Configures the LAN for gateway or client operation modes.
Details Gateway mode operations, cellular connection, and Network Address Translation (NAT).
Details Client mode operations for Ethernet connection to enterprise or home networks.
Configures location, alarming, logging, email, and dashboard display settings for applications.
Routes WAN IP traffic arriving on a specific port to a designated LAN side address.
Configures the physical electrical and timing characteristics of the serial ports.
Configures the serial (TCP/UDP/PPP) pad function for serial port options.
Allows configuration of up to 2 GRE tunnels over the cellular wireless interface.
Supports 8 concurrent IPsec tunnels with configuration options for secure communication.
Configures tunnel selection and security level globally for IPsec tunnels.
Defines tunnel-specific parameters for Phase 1 and Phase 2 of IPsec key exchange.
Synchronizes time using cellular network, NTP server, or GPS/GLONASS data.
Sets location source from built-in GPS/GLONASS receiver or user-defined coordinates.
Configures Dynamic Domain Name Service (DDNS) and cloud-based access/management system.
Mechanism to load over-the-air firmware updates and enable additional applications.
Manages backup and restore operations for system data via a USB stick.
Information on the standard Automation-Light application and licensing.
General| Brand | CTEK |
|---|---|
| Model | Z45 Series |
| Category | Controller |
| Language | English |
To Next Page