Curtis G3 Series User Guide

Coffee Pulse Brew (combo units only) - selects the Coffee Pulse Brew pattern (Pre-Infusion must be Off to
BDDFTT5IFQVMTFCSFXQBUUFSOTFMFDUFEiUVOFTwPSDIBOHFTUIFnBWPSPGUIFDPGGFF0ODFBDDFTTFE~),
press the BREW button for which Pulse Brew needs to be changed. Press Ż or Ź to select the desired setting
(see guidelines below for information on various settings). Press ~ to save. Press Ź to display the subsequent
menu features.
When Coffee Pulse Brew is on, Pre-Infuson is disabled.
Pulse Brew Guidelines
• Filter pack type coffees typically extract better with the A and B pulse setting.
• Decaffeinated coffees typically extract better with the B pulse setting.
• High-yield coffees typically extract better with the C pulse setting. Of course, any of the A, B or C
TFUUJOHTNBZCFVTFEUPTVJUZPVSUBTUFQSPmMF
• Settings D and E are manual pulse counts.
Coffee Drip-Out (combo units only) - sets the Coffee Drip-Out time. Drip-out allows additional time for coffee
to drain from the brew basket before “Brewing” disappears from the display. Once accessed (~), press the
BREW button for which the Drip-Out time needs to be changed (SHIFT+BREW selects half batch on some
models). Press Ż or ŹUPJODSFBTFPSEFDSFBTFUJNF5IFSBOHFJT0GGUP1SFTT~ to save. Press Ź to
display the subsequent menu features.
Safety Sw On/Off (combo units only) - turns the feature On and Off. Once accessed (
~), press Ż or Ź to
toggle between On and Off. Press ~ to save. Press Ź to display the subsequent menu features.
Temperature - adjusts the maximum tank water temperature. Once accessed (~), press Ż or Ź to
increase or decrease the temperature. The range is 170ºF to 208ºF. Press ~ to save. Press Ź to display the
subsequent menu features.
Energy Save Mode - saves energy during periods when the brewer is not in use. When set to On, the brewer
automatically shuts off four hours after the last brew cycle. Press the ON/OFF button to return to normal
operation. When set to On-140ºF, the brewer shuts off four hours after the last brew cycle, but the water tank
temperature remains at 140ºF. Use the On-140ºF setting to reach brewing temperature faster after periods
of non-use. Once accessed (~), press Ż or Ź to choose the desired setting. Press ~ to save. Press Ź to
display the subsequent menu features.
Brew Count Odom - When accessed, this feature displays the total brew cycles since the odometer was last
reset. Press Ź to go back without resetting or ~ to reset. Press Ź to display the subsequent menu features.
Brew Count Total - when accessed (~), displays the total brew cycles on the brewer. It cannot be reset. The
display returns to the previous screen automatically after a few seconds. Press Ź to display the subsequent
menu features.
PROGRAMMING GUIDE PG4
8$130(3"..*/((6*%&ø "
Setting Description
A Starts at beginning of brew cycle. 4 cycles of 10 seconds on and 5 seconds off, then on until end of brew cycle.
B
Starts towards end of brew cycle. 4 cycles of 5 seconds off and 4 cycles of 10 seconds on. Ends when brew cycle
ends.
C Starts at beginning of brew cycle. 5 cycles of 25 seconds on and 10 seconds off, then on until end of brew cycle.
D
Manually set. Starts at beginning of brew cycle. Number of pulses is adjustable from 1 to 20. Pulse on time and off
time are both adjustable from 5 to 150 seconds, in 5 second increments.
E
Manually set. Starts at beginning of brew cycle. Number of pulses is adjustable from 1 to 8. Pulse on time and off
time are both adjustable from 1 to 150 seconds.

Curtis G3 Series Specifications

General

Brand	Curtis
Model	G3 Series
Category	Brewing Systems
Language	English