Curtis G3 Series User Guide

PROGRAMMING GUIDE PG4
Cold Brew Lock - adjusts the temperature at which the brewer will brew when a BREW button is pressed
(Ready to brew appears on the display). This feature also adjusts the temperature at which the heating
FMFNFOUUVSOTPOUPSFIFBUUIFXBUFSJOUIFUBOL5IFBWBJMBCMFTFUUJOHTBSF¡'¡'BOE0GG0GGJTXJUIJO¡'
below the temperature setting. Once accessed (~), press Ż or Ź to select the desired setting. Press ~ to
save. Press Ź to display the subsequent menu features.
Master Reset - resets the brewer universal control module (UCM) to the factory default settings. Once
accessed (
~), “Are You Sure?” will appear on the display. Press Ż for Yes or Ź for No. If you press No, the
display goes back to the programming menu. If you press Yes, the UCM will reset and exit programming
mode.
IMPORTANT: If you reset the UCM to the factory defaults, you MUST reprogram the Model Select to
match the number on the model number label and the label on the UCM for proper operation.
Service Call - sets the service phone number that appears on the display when the UCM detects a SENSOR
ERROR or WATER ERROR. Once accessed (~), press Ż or Ź to select the number to be changed. Press ~
repeatedly
to change the number value. Press Ż or Ź to select the next number to change. When done, press
ŹVOUJMFYnBTIFTPOUIFEJTQMBZBOEQSFTT~. Press Ź to display the subsequent menu features.
Access Code - sets the access code entered to access programming mode (the factory default is 1-2-3-4).
Once accessed (~), press Ż or Ź to select the number to be changed. Press ~ repeatedly to change the
number value. Press Ż or Ź to select the next number to change. When done, press ŹVOUJMFYnBTIFTPOUIF
display and press ~. Press Ź to display the subsequent menu features.
Banner Name - changes the banner name that appears on the display. No banner name appears when all
blanks are entered. Once accessed (
~), press Ż or Ź to select the letter to change. Press ~ repeatedly to
change the letter. When done, press ŹVOUJMFYnBTIFTPOUIFEJTQMBZBOEQSFTT~. Press Ź to display the
subsequent menu features.
P-Maintenance - adjusts the P-Maintenance (preventive maintenance) brew monitor. When on, the UCM
measures the number of gallons brewed before the P-Maintenance reminder appears on the display. The
range is Off to 3000 gallons. Once accessed (~), press Ż or Ź to select the desired setting, then press ~ to
save. Press Ź to display the subsequent menu features.
Beeper On/Off - turns the beeper that is heard each time a button is pressed. Once accessed (
~), press Ż or
Ź to toggle between On and Off. Press ~ to save. Press Ź to display the subsequent menu features.
Quality Timer -OPUJmFTUIFVTFSUIBUUIFDPGGFFUFBJTOPMPOHFSGSFTICZNPOJUPSJOHUIFBNPVOUPGUJNFTJODF
the BREW button was last pressed. When time expires, an audio alarm turns on and Quality TimernBTIFTPO
the display. Once accessed (~), press Ż or Ź to increase or decrease the amount of time. The range is Off to
10 hours. Press ~ to save. Press Ź to display the subsequent menu features.
Displ. Brew Time - turns the display of the brew time during brewing On and Off. Once accessed (~), press
Ż or Ź to toggle between On and Off. Press ~ to save. Press Ź to display the subsequent menu features.
Display Messages - turns display of the message “Rinse Server Before Brewing” On or Off. Once accessed
(~), press Ż or Ź to toggle between On and Off. Press ~ to save. Press Ź to display the subsequent menu
features.
Model Select - changes the UCM to operate according to the model number. For proper operation, the model
selected must match the model number label on the outside of the machine. Once accessed (~), press Ż or
Ź until the model number matching the model number label on the brewer appears, then press ~. The UCM
will reset and exit programming mode.
8$130(3"..*/((6*%&ø "

Curtis G3 Series Specifications

General

Brand	Curtis
Model	G3 Series
Category	Brewing Systems
Language	English