Why is my Cyrus CLASSIC AMP remote control not working?
If the remote control for your Cyrus Amplifier isn't working, first check the batteries. If the remote control lights flash, this indicates that the batteries are flat and need replacing.
What to do if my Cyrus Amplifier shows an 'Error - Output' message?
If you see an 'Error - Output' message on your Cyrus Amplifier, it's usually due to a short-circuit at the loudspeaker terminals. To resolve this, switch off the amplifier and check for any short circuits in the speaker wiring, both at the amplifier's rear panel and at the speaker terminals.
Why is there no sound coming from my Cyrus Amplifier?
If your Cyrus Amplifier has no sound, consider these possible causes and solutions: * Check if the amplifier is switched on and not in Standby mode (the Standby light should be GREEN). * Ensure that Mute is deselected. * Verify that the connected source is working correctly (e.g., a CD is playing, not paused). * Confirm that the sample rate and sound format of the digital signal from the source are compatible with the amplifier's specifications and encoded as two-channel stereo.
How to fix a 'Error - Temperature' on Cyrus CLASSIC AMP?
The 'Error - Temperature' on your Cyrus Amplifier indicates temperature-related issues. The amplifier will lock in standby until it cools down. If this occurs frequently, improve ventilation around the amplifier. If the problem persists, your speakers' impedance rating may be too low.
What to do if one loudspeaker has no sound with my Cyrus CLASSIC AMP?
If you're getting no sound from one loudspeaker connected to your Cyrus Amplifier, try these solutions: 1. Make sure the BAL (balance) control is not at an extreme limit; centralize it. 2. Check if your speaker has fuses and replace them if necessary. 3. Inspect the speaker cables and interconnects for faults; check connections and replace cables if needed.
How to stop spurious noises from speakers connected to my Cyrus CLASSIC AMP?
If you're experiencing spurious noises from the speakers connected to your Cyrus Amplifier, the issue might be with faulty interconnects or connections. Check these and replace them where necessary to resolve the problem.
Connect the IEC connector and verify mains voltage compatibility.
Ensure safe operation by terminating speaker cables with supplied dual speaker plugs.
Refer all servicing to qualified personnel; do not attempt user repairs.
Contact authorised Cyrus service centers for technical advice and service.
Congratulations on your purchase and encouragement to register your product.
Check included accessories and select a well-ventilated location for installation.
Instructions on how to adjust the product's feet for leveling.
Diagram and key for connecting components to the rear panel.
Essential safety warning to disconnect mains before making audio connections.
Guide to connecting stereo audio interconnect cables to analogue inputs AN1-AN4.
Instructions for connecting digital audio sources using optical or phono interconnects.
How to connect turntables with moving-magnet cartridges to the PHONO/MM input.
Instructions for connecting speakers using supplied dual speaker plugs, observing polarity.
How the fixed output feeds sound at full volume to other devices.
Connecting Cyrus and non-Cyrus surround decoders for multi-channel audio.
How to create an MC-BUS loop for unified system control and power management.
Information about the PSX-R DC power supply for sonic performance upgrade.
Connect the AC power cable to the amplifier's power inlet and a mains point.
Labels and functions of buttons and indicators on the front panel.
Guidance on mains power, standby, and auto-standby features.
How to select audio inputs and special inputs like 'Cyrus AV'.
Instructions for connecting and using headphones.
How to play back and record audio using 'Fixed Out'.
The remote controls Cyrus components and can be programmed.
Step-by-step guide to installing AAA batteries into the remote control.
How to set the remote to Cyrus mode and send commands to components.
List of remote control commands for operating the Cyrus amplifier.
List of remote control commands for operating a Cyrus CD player.
List of remote control commands for operating a Cyrus audio streamer.
Commands for controlling the Cyrus Phono Signature via the remote.
Rename analogue and digital inputs from a predefined list.
Select one of three display modes for the amplifier's screen.
Adjust sensitivity for individual inputs to equalize source volumes.
Restore amplifier configuration to factory defaults, including input names and settings.
Information on how to upgrade the amplifier's operational firmware.
Checks, conditions, and steps for programming commands into the remote.
How to check learned commands and resolve learning issues.
Using the remote to send programmed commands to TV or Satellite receivers.
Covers no sound, single speaker issues, and spurious noises from speakers.
Addresses issues with remote control operation and battery status.
Explains specific error messages like Temperature, Output, PSU, and Mains faults.
Details line, phono, digital, and headphone audio performance specifications.
Details of the two-year warranty and WEEE disposal guidelines.
To Next Page
General
