D-Link DGS-1008P Installation Guide

CONTENTS
DGS-1008P 8-Port Gigabit Unmanaged Desktop PoE Switch
Power Adapter (54 V, 1.67 A)
Power Cable
Mounting Kit
4 Rubber Feet
Quick Install Guide
If any of these items are missing from your packaging, contact your reseller.
Warning: Using a power adapter with a different voltage rating will damage and void the warranty of this product.
INTRODUCTION
The D-Link DGS-1008P 8-Port Gigabit Unmanaged Desktop PoE Switch is capable of feeding power to Power over Ethernet
(PoE) devices such as network cameras. The DGS-1008P has 8 ports operating at 10/100/1000 Mbps with 4 PoE+ ports
(Ports 1 to 4) with a total PoE budget of 80W, making it ideal for home and small office use.
PRODUCT SETUP
BEFORE SETTING UP THE DGS-1008P
Please follow the steps below to set up the switch:
1. Install the DGS-1008P in a cool and dry place. Refer to the Technical Specifications for the acceptable operating
temperature and humidity ranges.
2. Install the switch in a site free from strong electromagnetic sources, vibration, dust, and direct sunlight.
3. Leave at least 10 cm of space at the left and right-hand sides of the switch for ventilation.
4. Visually inspect the power jack and make sure that it is fully secured to the power adapter.
Do not stack any device on top of the switch.
MOUNTING
You may mount the switch on a wall with the included mounting kit. Two mounting slots are provided on the bottom of
the switch for this purpose.
Magnet mounting is an optional method to mounting the switch on a wall and is not included with the package contents.
CONNECTING THE DGS-1008P TO YOUR NETWORK
A. POWER
Plug the AC power cord into a free outlet or surge protector, then plug the other end of the DC power jack into the power port
of the DGS-1008P. The Power LED will illuminate confirming that the device has powered up successfully.
B. PoE PORTS (PORTS 1 – 4)
PoE Ports 1 to 4 support 802.3at for up to 30W per port for individual usage.
C. GIGABIT PORTS (PORTS 1 – 8)
These ports offer network speeds of either 10 Mbps, 100 Mbps, or 1000 Mbps and can operate in half or full-duplex transfer
modes. These ports also support automatic MDI/MDIX crossover, eliminating the need for crossover cables or uplink ports.
Each port can be connected directly to a server, hub, router, or switch using regular straight-through twisted-pair Ethernet
cables.

D-Link DGS-1008P Specifications

General

MAC address table	8000 entries
Store-and-forward	Yes
Packet buffer memory	0.256 MB
Packet forwarding rate (1 Gbps)	14880 pps
Packet forwarding rate (10 Mbps)	1488000 pps
Packet forwarding rate (100 Mbps)	148800 pps
10G support	No
Networking standards	IEEE 802.3, IEEE 802.3ac, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x
Cable types supported	Cat3, Cat4, Cat5, Cat5e
Copper ethernet cabling technology	10BASE-T, 100BASE-T, 1000BASE-T
Switch type	Unmanaged
Power connector	DC-in jack
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
Product color	Black
Rack mounting	-
LED indicators	Activity, Link, PoE, Power, Speed, Status
Total Power over Ethernet (PoE) budget	68 W
Power over Ethernet (PoE) ports quantity	4
Power over Ethernet (PoE) power per port	30 W
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 95 %
Input current	1.5 A
Noise level	0 dB

Weight and Dimensions

Depth	120 mm
Width	190 mm
Height	38 mm