EasyManuals Logo

D-Link DWR-932 Quick Start Guide

D-Link DWR-932
2 pages
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
eu.dlink.com
Does this product automatically reconnect if the
mobile signal is lost due to inactivity? (Installation in an
unmanaged premises)
Yes - It will reconnect when the signal is requested or
available again.
Can this product be used as a failover solution?
A router is advisable as it will be plugged in
Can this product be used for gaming?
Yes - We recommend a ping and speedtest, such as Ookla
(www.speedtest.net)
Can this product be used in a caravan?
Yes, If you have a caravan
This is battery powered
Can this product be wall mounted?
No
Can this product be connected to an existing DSL / Fibre /
cable modem?
Yes, the device has a separate WAN port which allows you to
connect a xDSL modem.
In your prefered browser navigate to 192.168.0.1 in your
search bar to get to the admin page. Login with your
password (admin/admin by default)
In the WAN settings of your device you can change the type
of connection (DHCP or PPPoE) and enter any username and
password settings required for your connection.
Which kind of products can be connected via Ethernet
and / or Wi-Fi?
Any product can be connected, as long as they are complaint
with Wi-Fi standards
Typically connected products would be Cameras, VoiP
phones, Laptops Ipads etc.
Which dynamic DNS providers are supported?
All Dynamic DNS providers are supported using the custom
DNS provider settings.
Is it possible to remove the external 4G antennas and
replace them with high gain indoor or outdoor antennas?
n/a
Which connector type standard is used for the external
antennas?
n/a
Is it possible to turn off the Wi-Fi wireless connection for
safety reasons?
Yes, the devices broadcast settings can be disabled from
within the settings.
Open your prefereed browser and connect to the device on
its default IP address of 192.168.0.1.
Navigate to the Wireless settings and disable the SSID
broadcast.
Are the 2.4GHz and 5GHz SSIDs broadcast with different
names?
Yes, the device has a seperate 2.4ghz and 5Ghhz broadcast
and by default will come with different names to identify the
seperate bands.
It is not recommended to use the same SSID name for bothhe
2.4Ghz and 5Ghz broadcast on this product as there is no
bandsteering feature.
How many Ethernet ports are available? Which is the
maximum supported speed?
n/a
I need to extend the wireless coverage further. Is there
any recommended range extender?
Yes, we would recommend you talk to our support team for
the best option, as it can often depend on your environment
Visit https://eu.dlink.com/uk/en/support/contact to raise a
support case or livechat

Other manuals for D-Link DWR-932

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the D-Link DWR-932 and is the answer not in the manual?

D-Link DWR-932 Specifications

Radio Frequency Bands IconRadio Frequency Bands
FDD-LTE bandsBand 1, 3, 7, 8, 20
TDD-LTE band38
UMTS bandsB1-2100 MHz / B8-900 MHz
Cellular Access IconCellular Access
GSM bands850/900/1800/1900 MHz
LTE output power class23 dBm (class3)
Downlink speed100 Mbps
Wi-Fi Specifications IconWi-Fi Specifications
Wi-Fi standard 1802.11n
Wi-Fi standard 2802.11g
Wi-Fi standard 3802.11b
Physical Specifications IconPhysical Specifications
Dimensions96.8 x 57.6 x 15 mm (3.81 x 2.26 x 0.59 inches)
Weight90 g (3.17 ounces)
AntennaOne internal antenna
Operating Environment IconOperating Environment
Operating temperature0 to 40 °C (14 to 131 °F)
USB interfacemicro USB port
USIM slotStandard 6-pin SIM card interface

Related product manuals