D-Link Wireless Router

©2009 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and MediaBridge are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States and/or other countries. Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. Other trademarks or registered
trademarks are the property of their respective owners.
2
START hERE:
ThERE ARE ThREE opERATing SySTEmS liSTEd bElow To Show inTRucTionS
on how To configuRE youR compuTER And bEgin ThE SETup pRocESS.
OPTION 1: WINDOWS
®
XP
OPTION 2: WINDOWS VISTA
®
OPTION 3: WINDOWS 7
OPTION 1 - XP
OPTION 2 - Vista
OPTION 3 - Windows 7
1
Begin by connecting the power cable to the DAP-1360. Then, connect your ethernet
cable to the device’s LAN port on the back.
Once your PC is connected to the device, go to the computer’s taskbar and click
on START, then select Control Panel.
In Control Panel, open “Network Connections”.
When you have opened the “Network Connections” window, select and right-click
the “Local Area Connection” icon and click on properties. After the window has been
opened, look for the option “Internet Protocol” (TCP/IP) and click properties.
Once you have opened the properties window, select the “Use the following IP
address” option. The text boxes below will allow you to type the manual IP address.
In the category “IP address” type, “192.168.0.51”. Click the “Subnet Mask:” text box
and the address “255.255.255.0” will appear. You may leave the “Default Gateway,”
“Preferred DNS Server” and “Alternate DNS Server”. Then click “OK”.
You have successfully configured your computer to access the device’s web-based
configuration. Please proceed to the Range Extender guide on the reverse side of
this guide.
Connect the power cable to the router. Then connect your ethernet cable to the
DAP-1360’s LAN port on the back.
Once connected, go to the computer’s taskbar and select START. Then, right-click
NETWORK and click PROPERTIES.
In the “Network Connections” window, right-click the LOCAL AREA CONNECTION
icon and click PROPERTIES. When the window opens, select “Internet Protocol
Version 4 (TCP/IPv4)” and click PROPERTIES.
2
3
4
5
6
1
2
3
4
6
Connect the power cable to the router. Then connect your ethernet cable to the
DAP-1360’s LAN port on the back.
Set up the network and security settings to match your network settings. Refer to
the manual on the included CD for detailed information on this setup.
You have successfully configured your computer to access the device’s web-based
configuration. Please proceed to the Range Extender guide on the reverse side of
this guide.
1
2
3
5
6
4
Once you have opened the properties window, select the “Use the following IP
address” option. The text boxes below will allow you to type the manual IP address.
In the category “IP address” type, “192.168.0.51”. Click the “Subnet Mask:” text
box and the address “255.255.255.0” will appear. You may leave the “Default
Gateway,” “Preferred DNS Server” and “Alternate DNS Server”. Then click “OK”.
You have successfully configured your computer to access the device’s web-based
configuration. Please proceed to the Range Extender guide on the reverse side of
this guide.
Once connected, go to the computer’s taskbar and select START. Then, right-click
NETWORK and click PROPERTIES.
In “Network and Sharing Center,” click on “Manage Network Connections” on the
left side.
In “Network and Sharing Center,” click on “Manage Network Connections” on the
left side.
Once you have opened the properties window, select the “Use the following
IP address” option. The text boxes below will allow you to type the manual IP
address. In the category “IP address” type, “192.168.0.51”. Click the “Subnet
Mask:” text box and the address “255.255.255.0” will appear. You may leave the
“Default Gateway,” “Preferred DNS Server” and “Alternate DNS Server”. Then
click “OK”.
DAP -13 60
5V 3A
LAN
RESET
5V 3A
LAN
RESET
DAP-136 0
wireless rout er DIR-655
1 2 3 4
DAP-136 0
wireless rout er DIR-655
1 2 3 4
DAP-136 0
wireless route r DIR-655
1 2 3 4
DAP -13 60
DAP -13 60
5V 3A
LAN
RESET
5V 3A
LAN
RESET
DAP-136 0
wireless rout er DIR-655
1 2 3 4
DAP-136 0
wireless rout er DIR-655
1 2 3 4
DAP-136 0
wireless route r DIR-655
1 2 3 4
DAP -13 60
DAP -13 60
5V 3A
LAN
RESET
5V 3A
LAN
RESET
DAP-136 0
wireless rout er DIR-655
1 2 3 4
DAP-136 0
wireless rout er DIR-655
1 2 3 4
DAP-136 0
wireless route r DIR-655
1 2 3 4
DAP -13 60
DAP -1 360
5V 3A
LAN
RESET
5V 3A
LAN
RESET
DAP-13 60
wireles s rout er DIR-655
1 2 3 4
DAP-13 60
wireles s rout er DIR-655
1 2 3 4
DAP-13 60
wireless rout er DIR-655
1 2 3 4
DAP -13 60
DAP -1 360
5V 3A
LAN
RESET
5V 3A
LAN
RESET
DAP-13 60
wireles s rout er DIR-655
1 2 3 4
DAP-13 60
wireles s rout er DIR-655
1 2 3 4
DAP-13 60
wireless rout er DIR-655
1 2 3 4
DAP -13 60
DAP -1 360
5V 3A
LAN
RESET
5V 3A
LAN
RESET
DAP-13 60
wireles s rout er DIR-655
1 2 3 4
DAP-13 60
wireles s rout er DIR-655
1 2 3 4
DAP-13 60
wireless rout er DIR-655
1 2 3 4
DAP -13 60
INITIAL SETUP GUIDE
noTE:
Before you begin, make sure you have administrative
permission to modify the computer’s network settings.
5

D-Link Wireless Router Specifications

General

Brand	D-Link
Model	Wireless Router
Category	Wireless Router
Language	English

Summary

Configure Windows XP for Network Setup

Initial Connection and Control Panel Access

Connect device, access Control Panel, and open Network Connections.

Configure TCPIP Settings

Access TCP/IP properties and set IP address and subnet mask.

Setup Completion

Confirmation of successful configuration for accessing the device.

Configure Windows Vista for Network Setup

Initial Connection and Network Settings

Connect device, access Network settings, and manage connections.

Configure TCPIP Settings

Access TCP/IP properties and set IP address and subnet mask.

Setup Completion

Confirmation of successful configuration for accessing the device.

Configure Windows 7 for Network Setup

Initial Connection and Network Settings

Connect device, access Network settings, and manage connections.

Configure TCPIP Settings

Access TCP/IP properties and set IP address and subnet mask.

Setup Completion

Confirmation of successful configuration for accessing the device.

Setup DAP-1360 in Repeater Mode

Initial Connection and Setup Wizard

Connect device to PC, open browser, and launch wireless setup wizard.

Configure Repeater Mode Settings

Select Auto Mode, PBC, and connect via WPS for repeater setup.

Finalizing Setup and Placement

Disconnect device, adjust PC settings, and place device for use.

Setup DAP-1360 in AP Mode

Initial Connection and Setup Wizard

Connect device to PC, open browser, and launch wireless setup wizard.

Configure AP Mode Settings

Select configuration method, device name, and password for AP mode.

Wireless Network Details and Finalizing

Save network details, adjust PC settings, and connect wirelessly.

Setup DAP-1360 in Wireless Client Mode

Initial Connection and Setup Wizard

Connect device to PC, open browser, and launch wireless setup wizard.

Configure Client Mode Settings

Select device name, password, and connect via WPS for client mode.

Finalizing Setup and Connections

Adjust PC settings, reconnect device, and connect to other products.