Why is my Daewoo DWD-F1031 making a thumping sound?
If your Daewoo Washer is making a thumping sound, it's likely due to a heavy wash load, which is usually normal. However, if the sound persists, the washer may be out of balance. Stop the washer and redistribute the wash load.
What to do if the Daewoo Washer door does not open?
If your Daewoo Washer door won't open, wait two minutes to allow the electric locking mechanism to release after the cycle has stopped. The door is designed to remain locked for safety reasons once a cycle has started.
What to do if my Daewoo DWD-F1031 Washer shows a drain error?
If your Daewoo Washer is displaying a drain error, it could be due to several reasons. First, check the drain hose for any kinks or clogs and clean or straighten it. Other potential causes include a defective drain motor, valve inlet, or water level sensor, all of which would require replacement. It's also possible that the PCB ASS’Y is not checking the water level, which would also require replacement.
What does it mean when my Daewoo DWD-F1031 shows a thermistor wash overheating error?
A thermistor wash overheating error on your Daewoo Washer can occur if the heater operated without water in the tub; check the water level. It may also indicate that the thermistor wash is defective and needs to be replaced.
How to troubleshoot E5 HIGH VOLTAGE ERROR on Daewoo DWD-F1031?
The E5 HIGH VOLTAGE ERROR on your Daewoo washer can occur if laundry is jammed between the gasket and the drum; rearrange the laundry. If the issue persists, the PCB ASS’Y may be faulty and require replacement.
How to troubleshoot H2 THERMISTOR WASH ERROR on Daewoo DWD-F1031?
To resolve the H2 THERMISTOR WASH ERROR on your Daewoo Washer, you should change the thermistor wash. Also check the connector of the thermistor wash.
What to do if my Daewoo Washer shows a door open error?
If your Daewoo Washer displays a door open error, make sure the door is fully closed. If the Start/Hold button was pressed while the door was open, simply close the door. If the error persists, the switch door lock may be defective and need to be replaced. It's also possible that the PCB ASS’Y is not checking the door lock, and would also require replacement.
How to resolve H8 HEATER WASH OVERHEATING ERROR on Daewoo Washer?
To resolve the H8 HEATER WASH OVERHEATING ERROR on your Daewoo washer, it indicates that the heater worked without water in the tub. Check the water level and the heater wash.
What to do if my Daewoo Washer is making a vibrating noise?
If your Daewoo washer is making a vibrating noise, check if all the transit bolts and packing have been removed. If not, refer to the Installation guide for removing transit bolts. Also, make sure all the feet are resting firmly on the ground. An uneven wash load may also cause vibration; stop the washer and rearrange the load.
What to do if my Daewoo DWD-F1031 leaks water?
If your Daewoo Washer is leaking water, check and tighten the inlet and drain hose connections at both the tap and the washer itself. Additionally, inspect your house drain pipes for clogs and unclog them. If the problem persists, it may be necessary to contact a plumber.
General| Capacity | 10 kg |
|---|---|
| Washing capacity | 10 kg |
| Spin Speed | 1400 RPM |
| Maximum spin speed | 1400 RPM |
| Energy Efficiency Class | A+++ |
| Energy Rating | A+++ |
| Dimensions (W x H x D) | 600 x 850 x 600 mm |
| Dimensions (HxWxD) | 850 x 600 x 600 mm |
| Water Consumption | 50 L |
| Weight | 70 kg |
| Color | White |
| Loading type | Front Load |
To Next Page
