To Next PageTo Next PageWhy does my Daewoo Washer not start?
If your Daewoo Washer isn't starting, ensure the power cord is securely plugged into the wall outlet. Also, check your house fuse or circuit breaker; reset the breaker or replace the fuse if necessary, without increasing its capacity. If a circuit overload is the issue, consult a qualified electrician. Finally, make sure the water supply tap is turned on.
What to do if the Daewoo DWD-F1043 door does not open?
If your Daewoo Washer door won't open, wait two minutes to allow the electric locking mechanism to release after the cycle has stopped. The door is designed to remain locked for safety reasons once a cycle has started.
What to do if my Daewoo DWD-F1043 leaks water?
If your Daewoo Washer is leaking water, check and tighten the inlet and drain hose connections at both the tap and the washer itself. Additionally, inspect your house drain pipes for clogs and unclog them. If the problem persists, it may be necessary to contact a plumber.
How to fix Daewoo Washer that does not drain?
If your Daewoo Washer is not draining water properly or is draining slowly, begin by checking the drain hose for any kinks or clogs; clean and straighten the hose if needed. Also, inspect the drain filter for any blockages and clean it thoroughly.
How to fix Daewoo Washer that will not spin?
If your Daewoo Washer is not spinning, make sure that the door is firmly shut. Close the door properly and press the Start/Pause button. Note that it may take a few moments after pressing the button for the washer to begin spinning, as the door must lock first.
How to fix E4 LEAKAGE ERROR on Daewoo Washer?
To resolve the E4 LEAKAGE ERROR on your Daewoo Washer, check for leaks in the tub or the hose drain. Then change the tub or the hose drain.
How to fix E9 SENSOR PRESSURE ERROR on Daewoo DWD-F1043 Washer?
To resolve the E9 SENSOR PRESSURE ERROR on your Daewoo Washer, you should change the water level sensor.
How to fix H5 WATER TEMP. ERROR on Daewoo DWD-F1043 Washer?
To resolve the H5 WATER TEMP. ERROR on your Daewoo Washer, you should change the thermistor wash.
How to fix PFE PUMP FILTER ERROR on Daewoo Washer?
To resolve the PFE PUMP FILTER ERROR on your Daewoo Washer, clean the drain pump filter. If problems persist you should change the drain pump. Also use the proper amount of detergent and place the drain hose 1m below the floor.
Why is my Daewoo DWD-F1043 making a vibrating noise?
If your Daewoo Washer is making a vibrating noise, ensure all transit bolts and packing have been removed according to the installation guide. If the noise continues, it could be due to an uneven wash load. Stop the washer and rearrange the load to balance it.
General| Washing capacity | 6 kg |
|---|---|
| Spin speed | 1000 RPM |
| Capacity | 6 kg |
| Number of Programs | 15 |
| Color | White |
| Type | Front Load |
| Loading type | Front |
| Energy Rating | A |
Instructions for removing transit bolts to prevent internal damage during transport.
Guidelines for choosing a suitable installation location and ensuring levelness.
Step-by-step guide for connecting the water inlet hose to the washing machine.
Procedures for correctly installing the drain hose to prevent leaks and noise.
How to adjust the machine's legs for stability and reduce vibration.
Methods for cleaning the washing machine's exterior surfaces and interior drum.
How to clean the water inlet filter to resolve water supply issues.
Instructions for cleaning the drain pump filter to ensure proper drainage.
Procedures for cleaning the detergent case and the washing drum.
Common symptoms, their causes, and recommended solutions.
Explanation of error messages, their causes, and troubleshooting steps.
