Daewoo DWD-HB143 Series

Questions and Answers

T
Tracey GillespieSep 23, 2025
How to fix HP HIGH POWER ERROR on Daewoo DWD-HB143?
- E
  Elizabeth GonzalezSep 23, 2025
  If your Daewoo Washer displays an HP HIGH POWER ERROR, it will disappear when the input voltage drops below 270V.
J
James JohnsonAug 25, 2025
How to fix a Daewoo DWD-HB143 that won't spin?
- D
  Diana SmithAug 25, 2025
  If your Daewoo Washer won't spin, ensure the door is firmly shut. Close the door and press the Start/Pause button. Note that after pressing the button, it may take a few moments before the washer begins to spin, as the door must lock first.
D
Darius DavisAug 25, 2025
What to do if my Daewoo Washer door does not open?
- R
  Rebecca HarrisAug 26, 2025
  If the door of your Daewoo Washer won't open, wait two minutes after the wash cycle has ended. This allows the electric locking mechanism time to release for safety reasons.
H
Heather SmithAug 27, 2025
How to fix IE WATER INLET ERROR on Daewoo Washer?
- K
  Kathryn SimpsonAug 27, 2025
  To fix an IE WATER INLET ERROR on your Daewoo Washer: - Open the water tap. - Clean the filter of the valve inlet. - Change the valve inlet. - Change the water level sensor (sensor pressure). - Change the drain motor. - Change the PCB ASS?Y.
C
catherine62Aug 27, 2025
How to fix UE UNBALANCE ERROR on Daewoo Washer?
- W
  wilsonmelissaAug 27, 2025
  If your Daewoo Washer displays a UE UNBALANCE ERROR, it means the laundry is concentrated on one side of the drum during the spin cycle. To fix this, simply rearrange the laundry inside the drum.
S
Sara DunnSep 13, 2025
How to fix E8 MOTOR ERROR on Daewoo Washer?
- D
  Deborah MillerSep 13, 2025
  To fix an E8 MOTOR ERROR on your Daewoo Washer: - Check the connector of the motor to ensure it is properly connected. - Change the motor if it is not working.
A
amartinezSep 12, 2025
How to fix E5 HIGH VOLTAGE ERROR on Daewoo DWD-HB143?
- B
  Bryan DavisSep 12, 2025
  To fix an E5 HIGH VOLTAGE ERROR on your Daewoo Washer: - Rearrange the laundry if it's jammed between the gasket and the drum. - Change the PCB ASS?Y.
K
Kerry TateSep 12, 2025
How to fix E6 EMG ERROR on Daewoo DWD-HB143 Washer?
- L
  lauren85Sep 12, 2025
  To resolve an E6 EMG ERROR on your Daewoo Washer: - Rearrange the laundry if it is jammed between the gasket and the drum. - Change the motor. - Change the PCB ASS?Y.
R
Renee RiveraSep 4, 2025
Why is my Daewoo DWD-HB143 making a thumping sound?
- A
  amber26Sep 4, 2025
  A thumping sound in your Daewoo Washer might be normal if you're washing a heavy load. However, if the sound continues, it could mean the washer is out of balance. Stop the washer and redistribute the wash load.
T
Teresa WalkerSep 2, 2025
Why is my Daewoo DWD-HB143 making a vibrating noise?
- C
  Candice GriffithSep 2, 2025
  Ensure all transit bolts and packing have been removed from your Daewoo Washer. If not, refer to the installation guide. Also, check that all the feet are resting firmly on the ground. An unevenly distributed wash load can also cause vibration, so stop the washer and rearrange the load.