Why Daikin FTKS35BVMB is not turning on? (OPERATION lamp is off)
If your Daikin Air Conditioner isn't turning on and the OPERATION lamp is off, check the following: * Ensure the breaker hasn't been turned OFF or a fuse hasn't blown. * Verify that there isn't a power failure. * Confirm that batteries are correctly installed in the remote controller. * Check if the timer setting is correct.
What to do if Daikin FTKS35BVMB operation stops suddenly? (OPERATION lamp is on)
If your Daikin Air Conditioner stops suddenly and the OPERATION lamp is on, it might be due to a sudden large voltage fluctuation. For system protection, the air conditioner automatically resumes operation in about 3 minutes.
Why Daikin FTKS35BVMB operation does not start soon?
If your Daikin Air Conditioner doesn't start immediately after pressing the ON/OFF button soon after stopping or reselecting the mode, wait for about 3 minutes.
Why Daikin FTKS35BVMB Air Conditioner outdoor unit emits water or steam?
The outdoor unit of your Daikin Air Conditioner may emit water or steam. This can occur in HEAT mode when frost on the outdoor unit melts during defrost operation. In COOL or DRY mode, moisture in the air can condense on the cool surface of the outdoor unit piping and drip.
How to improve cooling (heating) effect of Daikin FTKS35BVMB?
If you're experiencing poor cooling or heating with your Daikin Air Conditioner, consider these points: * Ensure the air filters are clean. * Make sure nothing is blocking the air inlet or outlet of the indoor and outdoor units. * Verify that the temperature setting is appropriate. * Confirm that windows and doors are closed. * Check if the airflow rate and direction are set correctly. * Check if the unit is set to the INTELLIGENT EYE mode.
Why my Daikin FTKS35BVMB smells bad?
If your Daikin Air Conditioner's indoor unit is emitting an odor, it's likely due to smells from the room, furniture, or cigarettes being absorbed into the unit and discharged with the airflow. If this occurs, it is recommended to have the indoor unit cleaned by a technician.
Why Daikin FTKS35BVMB hot air does not flow out soon after the start of heating operation?
If hot air doesn't flow out immediately after starting the heating operation on your Daikin Air Conditioner, allow 1 to 4 minutes for the system to warm up. The system is designed to discharge air only after reaching a certain temperature.
Why Daikin FTKS35BVMB Air Conditioner heating operation stops suddenly and a flowing sound is heard?
If the heating operation on your Daikin Air Conditioner stops suddenly and you hear a flowing sound, the system is likely removing frost from the outdoor unit. Wait for about 3 to 8 minutes.
Why does Daikin FTKS35BVMB release mists from the indoor unit?
Mists may come out of the indoor unit of your Daikin Air Conditioner when the air in the room is cooled into mist by the cold airflow during cooling operation.
General| Type | Split System |
|---|---|
| Mounting | Wall Mounted |
| Cooling Capacity | 3.5 kW |
| Heating Capacity | 4.0 kW |
| Refrigerant | R32 |
| Power Supply | 220-240V, 50Hz |
| Noise Level (Outdoor Unit) | 48 dB(A) |
| Indoor Unit Weight | 9 kg |
Provides technical specifications for the air conditioner units.
Detailed technical specifications for cooling-only models.
Detailed technical specifications for heat pump models.
Explains key operational features of the air conditioner.
Explains how the inverter controls compressor frequency.
Details the control logic and specifications for the unit.
Details how frequency is determined based on room and set temperatures.
Instructions specific to FTK(X)S 25/35 BVMB models.
Essential safety guidelines for operating and handling the unit.
Guidelines for cleaning the indoor unit, outdoor unit, and remote controller.
Common issues and their explanations or solutions.
Warnings and guidelines before performing diagnostic procedures.
Lists common symptoms and their corresponding checks and measures.
Guides for diagnosing and resolving operational faults.
Lists error codes displayed by the unit and their meanings.
Troubleshooting steps for an abnormal indoor unit PCB.
Diagnosis for freeze-up or high-pressure protection issues.
Steps to diagnose signal transmission errors between units.
Troubleshooting for insufficient gas conditions.
To Next Page
