How to fix abnormal functioning during Daikin FTXG25EV1BS Air Conditioner operation?
If you experience abnormal functioning during the operation of your Daikin Air Conditioner, try turning the breaker OFF, then turn it back ON. After that, attempt to operate the air conditioner again using the remote controller.
What to do if my Daikin FTXG25EV1BS Air Conditioner operation stopped suddenly?
If your Daikin Air Conditioner operation stopped suddenly, but the OPERATION lamp is still on, it will automatically resume operation in about 3 minutes.
Why is my Daikin FTXG25EV1BS Air Conditioner cooling (heating) effect poor?
If the cooling or heating effect of your Daikin Air Conditioner is poor, check the following: Ensure the air filters are clean. Make sure nothing is blocking the air inlet or outlet of either the indoor or outdoor units. Verify the temperature setting is correct. Confirm that windows and doors are closed. Check the air flow rate and air direction. Finally, see if the unit is set to INTELLIGENT EYE mode.
Why is the cooling/heating effect poor on my Daikin FTXG25EV1BS?
A poor cooling or heating effect in your Daikin Air Conditioner could be due to several reasons. Check that the air filters are clean and that nothing is blocking the air inlet or outlet. Ensure the temperature setting is appropriate, all windows and doors are closed, and the airflow rate and direction are correctly set. Also, verify if the unit is set to INTELLIGENT EYE mode.
What to do if my Daikin FTXG25EV1BS Air Conditioner indoor unit smells?
If your Daikin Air Conditioner's indoor unit emits an odor, it is recommended to have the indoor unit professionally cleaned by a technician.
Why does my Daikin FTXG25EV1BS indoor unit gives out odour?
If the indoor unit of your Daikin Air Conditioner is emitting an odor, it is recommended to have the indoor unit cleaned by a technician.
Why does hot air not flow out soon after I start heating operation on my Daikin Air Conditioner?
If hot air doesn't flow out immediately after starting the heating operation on your Daikin Air Conditioner, allow 1 to 4 minutes for it to begin.
What to do if my Daikin Air Conditioner does not operate and the OPERATION lamp is off?
If your Daikin Air Conditioner isn't operating and the OPERATION lamp is off, first check whether a breaker has tripped or a fuse has blown. Also, verify if there has been a power failure, ensure the batteries are correctly installed in the remote controller, and confirm that the timer setting is correct.
Why don't the flaps open when my Daikin Air Conditioner unit is started?
If you have a multi-system Daikin Air Conditioner, the flaps might not open if the unit starts during defrosting. In this case, the flaps will remain closed until the defrosting process is complete.
Why doesn't hot air flow out soon after starting the heating operation on my Daikin FTXG25EV1BS Air Conditioner?
After starting the heating operation on your Daikin Air Conditioner, you may need to wait for 1 to 4 minutes for hot air to flow out. The system is designed to start discharging air only after it has reached a certain temperature.
General| Brand | Daikin |
|---|---|
| Model | FTXG25EV1BS |
| Category | Air Conditioner |
| Language | English |
Covers critical warnings and cautions for safe operation and handling of the unit.
Identifies and describes the various parts of the indoor unit.
Explains the buttons and display functions of the remote controller.
Instructions for inserting batteries into the remote controller.
Provides advice on reducing energy consumption by adjusting settings and maintenance.
Specifies recommended operating conditions for different modes (COOL, HEAT, DRY).
Steps to select operation mode and start the air conditioner.
Steps to stop the air conditioner.
How to adjust the temperature setting for different modes.
How to adjust the air flow rate for different modes.
How to adjust the flap for desired air direction.
How to adjust the louvers for desired air direction.
How to activate and cancel 3-D airflow.
How to activate the comfort airflow mode for indirect air blowing.
How to deactivate the comfort airflow mode.
How to activate powerful mode for maximum cooling/heating effect.
How to deactivate the powerful operation mode.
How to activate quiet mode to reduce outdoor unit noise.
How to deactivate the outdoor unit quiet operation mode.
How to activate the intelligent eye sensor for energy saving.
How to deactivate the intelligent eye operation.
Explains how Intelligent Eye saves energy by adjusting temperature and airflow.
Details sensor detection range, sensitivity, and limitations.
Steps to set the timer to turn the unit off automatically.
How to cancel a set OFF timer.
Steps to set the timer to turn the unit on automatically.
How to cancel a set ON timer.
Example of setting both ON and OFF timers simultaneously.
How operation modes are selected and prioritized in multi-system setups.
Details on the night quiet mode for cooling operation.
How to use quiet operation with multi-system units.
How the priority room setting affects operation mode selection.
How powerful operation is prioritized based on the priority room.
How quiet operation is prioritized based on the priority room.
General cleaning instructions for the main components.
Detailed steps for opening, cleaning, and reattaching the front panel.
Steps for removing, cleaning, and replacing air filters and purifying filters.
Explains the consequences of operating with dirty filters.
Checks to perform before operating the unit.
Steps to prepare the unit for extended periods of non-use.
Explains common situations that are not actual troubles but have normal reasons.
Provides explanations for various operational issues and their causes.
Checks to perform before contacting a repair person.
Lists symptoms that indicate immediate need to call a service shop.
Instructions for proper disposal of the unit and batteries.
Importance and recommendation for professional periodic maintenance.
How to activate and use the remote controller for fault diagnosis.
List of error codes and their meanings for system and unit faults.
Explains the meaning of LED indicators on the outdoor unit PCB for fault detection.
To Next Page
