What to do if my Daikin Air Conditioner remote controller sensitivity is low?
If the remote controller sensitivity is low, replace all the batteries with new size AAA.LR03 (alkaline) batteries, as the current ones may be dying or the remote controller may be malfunctioning.
What to do if water leaks from the indoor unit of my Daikin FVXS60LVMA?
Call the service shop.
Why is the cooling or heating effect poor on my Daikin FVXS60LVMA?
The cooling or heating effect might be poor because the temperature setting is not appropriate, or the air filters need cleaning. Ensure that windows and doors are closed, and that the air flow rate and direction are set correctly. Clean the air filters if they are dirty.
Why is my Daikin FVXS60LVMA cooling effect poor?
Several factors can affect the cooling performance of your Daikin Air Conditioner. Please check the following: * Ensure the air filter is clean. * Verify that nothing is blocking the air inlet or outlet of both the indoor and outdoor units. * Confirm that the temperature setting is appropriate for your needs. * Make sure all windows and doors are closed properly. * Check that the airflow rate and air direction are set correctly.
What to do if my Daikin FVXS60LVMA operation stops suddenly?
If the Daikin Air Conditioner stops suddenly, check for any obstructions blocking the air inlet or outlet of the indoor and outdoor units. If there are obstacles, turn the breaker off, remove them, and then turn the breaker back on. Try operating the air conditioner again with the remote controller.
Why is my Daikin Air Conditioner cooling (heating) effect poor?
If the cooling or heating effect of your Daikin Air Conditioner is poor, try cleaning the air filter.
General| Type | Floor Standing |
|---|---|
| Cooling Capacity | 6.0 kW |
| Heating Capacity | 7.0 kW |
| Energy Efficiency Ratio (EER) | 3.21 |
| Refrigerant | R32 |
| Noise Level (Outdoor Unit) | 48 dB(A) |
| Power Supply | 220-240 V, 50 Hz |
| Indoor Noise Level | 30 dB(A) |
Critical safety instructions to prevent severe injury or death from improper operation.
Instructions to prevent property damage or minor injury due to incorrect use.
Safe operation, electrical safety, handling refrigerants, and environmental considerations.
Guidelines for proper and safe installation locations, considering environment and neighbors.
Details of indoor unit components, including filters, louvers, and control panel.
Identification of outdoor unit components like air inlet, outlet, and terminals.
Overview of the remote control buttons, display, and signal transmitter.
Instructions for installing batteries and operating the remote controller.
Procedure for setting the unit's clock, essential for timer functions.
How to start, stop, and change basic modes like AUTO, COOL, HEAT, DRY, FAN.
Steps to change the fan speed setting for different modes.
Adjusting the horizontal flap and vertical louvers for optimal airflow.
Choosing specific blowing patterns using the air outlet selection switch.
Maximizing cooling or heating effect for rapid temperature adjustment.
Reducing the noise level of the outdoor unit for quiet operation.
Limiting maximum power consumption for energy efficiency.
Scheduling automatic unit turn-off and turn-on times.
Programming daily and weekly operational schedules for personalized comfort.
Efficiently copying timer settings from one day to another.
Confirming, deactivating, and deleting programmed timer reservations.
Managing operation modes and priority settings in a multi-indoor unit system.
How the QUIET mode functions and interacts in a multi-system setup.
Forcing all connected indoor units to operate in a single mode (COOL or HEAT).
Steps for cleaning the indoor unit and remote controller.
Instructions for cleaning or replacing air filters and photocatalytic filters.
Effects of dirty filters and essential system checks before long idle periods.
Explanations for normal operational sounds and behaviors that are not faults.
Performing basic checks and diagnosing faults using error codes.
Critical issues requiring immediate attention and when to call a service shop.
Interpreting error codes displayed on the remote controller for troubleshooting.
To Next Page