Daikin FXSQ-TAVJU Series - Page 57

EDUS391777-F17 Installation Manual
FXSQ-TAVJU 2
3P184443-13Z
2
English
r Make sure that all wiring is secured, that specified wires
CTGWUGFCPFVJCVPQGZVGTPCNHQTEGUCEVQPVJGVGTOKPCN
connections or wires. Improper connections or installation
may result in fire.
r 9JGPYKTKPIRQUKVKQPVJGYKTGUUQVJCVVJGEQPVTQNDQZ
lid can be securely fastened. Improper positioning of the
EQPVTQNDQZNKFOC[TGUWNVKPGNGEVTKEUJQEMUHKTGQTVJG
terminals overheating.
r Before touching electrical parts, turn off the unit.
r This equipment can be installed with a Ground-Fault
Circuit Breaker (GFCI). Although this is a recognized
measure for additional protection, with the grounding
system in North America, a dedicated GFCI is not
necessary.
r When installing or relocating the system, keep the
refrigerant circuit free from substances other than the
specified refrigerant (R410A) such as air. Any presence of
air or other foreign substance in the refrigerant circuit can
cause an abnormal pressure rise or rupture, resulting in
injury.
r Do not change the setting of the protection devices. If the
pressure switch, thermal switch, or other protection device
is shorted and operated forcibly, or parts other than those
URGEKHKGFD[&CKMKPCTGWUGFHKTGQTGZRNQUKQPOC[QEEWT
CAUTION
r Do not touch the switch with wet fingers. Touching a switch
with wet fingers can cause electric shock.
r Do not allow children to play on or around the unit to
prevent injury.
r Do not touch the refrigerant pipes during and immediately
after operation as the refrigerant pipes may be hot or
cold, depending on the condition of the refrigerant flowing
through the refrigerant piping, compressor, and other
refrigerant cycle parts. Your hands may suffer burns or
frostbite if you touch the refrigerant pipes. To avoid injury,
give the pipes time to return to normal temperature or, if
you must touch them, be sure to wear proper gloves.
r *GCVGZEJCPIGTHKPUCTGUJCTRGPQWIJVQEWV
To avoid injury wear gloves or cover the fins when working
around them.
r Install drain piping to proper drainage. Improper drain
piping may result in water leakage and property damage.
r Insulate piping to prevent condensation.
r Be careful when transporting the product.
r Do not turn off the power supply immediately after
stopping operation. Always wait for at least 5 minutes
before turning off the power supply. Otherwise, water
leakage may occur.
r Do not use a charging cylinder. Using a charging cylinder
may cause the refrigerant to deteriorate.
r Refrigerant R410A in the system must be kept clean, dry,
and tight.
(a) Clean and Dry - Foreign materials (including mineral
oils such as SUNISO oil or moisture) should be pre-
vented from getting into the system.
(b) Tight - R410A does not contain any chlorine, does
not destroy the ozone layer, and does not reduce the
earth’s protection again harmful ultraviolet radiation.
R410A can contribute to the greenhouse effect if it is
released. Therefore take proper measures to check for
the tightness of the refrigerant piping installation. Read
the chapter Refrigerant Piping Work and follow the
procedures.
r Since R410A is a blend, the required additional refrigerant
must be charged in its liquid state. If the refrigerant is
charged in a state of gas, its composition can change and
the system will not work properly.
r The indoor unit is for R410A. See the catalog for indoor
models that can be connected. Normal operation is not
possible when connected to other units.
r Remote controller (wireless kit) transmitting distance
ECPDGUJQTVGTVJCPGZRGEVGFKPTQQOUYKVJGNGEVTQPKE
fluorescent lamps (inverter or rapid start types). Install the
indoor unit far away from fluorescent lamps as much as
possible.
r Indoor units are for indoor installation only. Outdoor units
can be installed either outdoors or indoors.
r Do not install the air conditioner or heat pump in the
following locations:
(a) Where a mineral oil mist or oil spray or vapor is pro-
FWEGFHQTGZCORNGKPCMKVEJGP
Plastic parts may deteriorate and fall off or result in
water leakage.
(b) Where corrosive gas, such as sulfurous acid gas, is
produced.
Corroding copper pipes or soldered parts may result in
refrigerant leakage.
(c) Near machinery emitting electromagnetic waves.
Electromagnetic waves may disturb the operation of
the control system and cause the unit to malfunction.
F9JGTGƃCOOCDNGICUOC[NGCMYJGTGVJGTGKUECTDQP
ƂDGTQTKIPKVCDNGFWUVUWURGPUKQPKPVJGCKTQTYJGTG
XQNCVKNGƃCOOCDNGUUWEJCUVJKPPGTQTICUQNKPGCTG
handled. Operating the unit in such conditions can
ECWUGCƂTG
NOTE
r Install the power supply and transmission wires for the
indoor and outdoor units at least 3.5 feet away from
televisions or radios to prevent image interference or
noise. Depending on the radio waves, a distance of 3.5
feet may not be sufficient to eliminate the noise.
r Dismantling the unit, treatment of the refrigerant, oil and
additional parts must be done in accordance with the
relevant local, state, and national regulations.
r Do not use the following tools that are used with
conventional refrigerants: gauge manifold, charge hose,
gas leak detector, reverse flow check valve, refrigerant
charge base, vacuum gauge, or refrigerant recovery
equipment.
r +HVJGEQPXGPVKQPCNTGHTKIGTCPVCPFTGHTKIGTCVQTQKNCTGOKZGF
in R410A, the refrigerant may deteriorate.
r This air conditioner or heat pump is an appliance that
should not be accessible to the general public.
r As design pressure is 478 psi, the wall thickness of field-
installed pipes should be selected in accordance with the
relevant local, state, and national regulations.