EasyManuals Logo
Home>Danfoss>Controller>EKC 331

Danfoss EKC 331 User Manual

Danfoss EKC 331
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
EKC 331 Instructions RI.8B.E1.52 © Danfoss 10/2000 5
ENGLISH
Literature survey:
Manual EKC 331 RS.8A.G-.--
Installation guide, Data communication link RC.8A.C-.--
Light-emitting diodes (LED) on front panel
There are four LEDs on the front panel which will light up
when the relays are operated.
All LEDs will flash if there is an error in the regulation. In this
situation you can upload the error code on the display and
cancel the alarm by pushing the top button briefly.
Display
The values will be shown with three digits, and with a setting
you can determine whether the temperature are to be shown
in bar or in psig.
Operation Menu survey
The buttons
When you want to change a setting, the two buttons will give
you a higher or lower value depending on the button you are
pushing. But before you change the value, you must have
access to the menu. You obtain this by pushing the upper
button for a couple of seconds - you will then enter the
column with parameter codes. Find the parameter code you
want to change and push the two buttons simultaneously.
When you have changed the value, save the new value by
once more pushing the two buttons simultaneously.
Gives access to the menu
(or cutout an alarm)
Gives access to changes
Saves a change
Examples of operations
Set the regulations reference
1. Push the two buttons simultaneously
2. Push one of the buttons and select the new value
3. Push both buttons again to conclude the setting
Set one of the other menus
1. Push the upper button until a parameter is shown
2. Push one of the buttons and find the parameter you want to
change
3. Push both buttons simultaneously until the parameter value
is shown
4. Push one of the buttons and select the new value
5. Push both buttons again to conclude the setting
Factory setting
If you need to return to the factory-set values, it can be done in this way:
- Cut out the supply voltage to the controller
- Keep both buttons depressed at the same time as you reconnect the supply
voltage
:segassemgniwollofehtevignacrellortnocehT
1E
egassemrorrE
rellortnocehtnisrorrE
2E
silangislortnocroegnarfotuonoitalugeR
.tcefed
1A
egassemmralA
mralaerusserphgiH
2AmralaerusserpwoL
noitcnuF-araP
retem
.niM.xaM
yalpsidlamroN
rettimsnarterusserpehtmorflangisehtswohS-rab
ecnerefeR
ecnerefererusserpsnoitalugerehtteS-rab1-rab04
enozlartueN10rrab1,0rab1
gnitteserusserpfonoitatimil.xaM20rrab1-rab04
gnitteserusserpfonoitatimil.niM30rrab1-rab04
)gisp=1/rab=0(tinutceleS50r01
tupniIDtalangisybtnemecalpsidecnerefeR31rrab5-rab5
mralA
)eulavetulosba(timilmralareppU01Arab1-rab04
)eulavetulosba(timilmralarewoL11Arab1-rab04
yaledemits'mralA30As1s003
yticapaC
syalerrofemitNO.niM10cs0s009
syalerfonitucrofyaledemiT50cs5s009
syalerfotuotucrofyaledemiT60cs5s009
yaleremasfosnitucneewtebdoirepemit.niM70cs0s009
edomnoitalugerfonoitinifeD
laitneuqeS:1
cilcyC:2
sredaolnuhtiwcilcyC:3
80c1 3
syalereht,detcelesneebsah3edomnoitalugerehtfI
:otdenifedebnacsredaolnuehtrof
deriuqersiyticapaceromnehwnituC:0
deriuqersiyticapaceromnehwtuotuC:1
90c01
suoenallecsiM
sserddasrellortnoC*30o1 06
)egassemnip-ecivres(hctiwsffo/nO*40o- -
edocsseccA50o)1-(ffo001
:noitacilppadnalangistupnienifeD
deppotsnoitaluger/langison:0
.gerrosserpmoc-rettimsnarterusserpAm02-4:1
.gerresnednoc-rettimsnarterusserpAm02-4:2
.gerrosserpmoc-rettimsnarterusserpR23SKA:3
.gerresnednoc-rettimsnarterusserpR23SKA:4
eludomyalerV01-0:5
eludomyalerV5-0:6
eludomyalerV01-5:7
01o0 7
egnahcuoynehW.)hsinad=3,hsilgne=0(egaugnaL
.40Oetavitcaoslatsumuoygnittessiht
*1100 3
ycneuqerfegatlovylppusteS21ozH05zH06
syalerxhtiwnoitarepolaunaM81o0 4
stuptuoyalerforebmunenifeD91o1 4
eulav.nim-egnargnikrowsrettimsnarterusserP02orab1-rab0
eulav.xam-egnargnikrowsrettimsnarterusserP12orab1rab04
:tupniIDenifeD
desuton:0
ecnerefersecalpsidtcatnoC:1
noitalugerspotsdnastratstcatnoC:2
22o0 2
)01semiteulav(1yalerfosruohgnitarepO32oh0h999
)01semiteulav(2yalerfosruohgnitarepO42oh0h999
)01semiteulav(3yalerfosruohgnitarepO52oh0h999
)01semiteulav(4yalerfosruohgnitarepO62oh0h999
neebsahleudomnoitacinummocatadafielbissopebylnolliwgnittessihT)*
.rellortnocehtnidellatsni

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Danfoss EKC 331 and is the answer not in the manual?

Danfoss EKC 331 Specifications

General IconGeneral
BrandDanfoss
ModelEKC 331
CategoryController
LanguageEnglish

Related product manuals