Danfoss Z-Wave RS - Page 6

lnstaLri.rlltG*
t*l§
Z-lYavef,ehrls
T}EZ-WbrrßS@ihifüdidLdiTdhr!
Z:kt€ rEtrcrk
with .ffis Z*brc
@fu
oh*:üom
rnry da Mtfuuc
All
cqrg|üy
poEEdz-ktrffi
müE-rcEffi r.il
*tas
repeats
Egad6 ditE
EmXü
Z-lYave best
pedic
.
Aftsa
qr@5§fr.a
t!d6irc'
üiE
@ü@klrctsd.W XE_UP_
lNTERar' L_sEI@nd
brüEzslcß n artuD
sFtiry
where
and wtH the
Z+tk i5
dEü mn- *eHy-
.
After
-nding
tt€ WAIE_tP_lüTtUitc._5Ef
@müd. ttE otroller
must
askJn
retun
rü.Ga
I üE Z-bE
qsc
Eiah G dEriEtion
i.e. the ndD
rd
irrtE
l{füE_1JP-HImilnL_5Fwd
.
The nodelD
*t
in
the WlIE_tP_r{TER[td.-*-f
@rEü
rur be
fora
perumttyEstairg&ar$-h
GprüEthe
mnds
sent trom th€ Z-Wü RS- füEq*irü[d
<ifheerded
periodt
the Z-Wre
flS ra
etlEtrü E@A6L
.
Although
thez-WreRsq+fqts*gbqmds
mslti(uF
mands
must alm)E be
led to
gEre
bB
&t friE
Z-Wave lnclusion
.
Ensure thatthe Z-WareR5irfadryreset
.
Activate
"lnclusion-
s ftE Z+Yüc düob-
.
Press the LED butts
fi tlEZ+tbrEn§
.
Obserye both controlls
ard Z{Vaß RS
fu sfzÖE driE
p.6
Z-Wave Exclusion
'
Activate 'Exclusion'
on the
Z-\ryrc @fiofs,
.
Hold down the 3 buttons
@ tlE Z-Wrc nS So.
5 recds
1{p,
dodn
and LED buftons).
.
Obserue both
controller and Z-Ware RS
fu. ffi6 of üE
p.@
lnstallation
& User Guide
Z-Wave RS
Z-Wave
WakeUp
A controller can only communicate
withthe
Z-Wave RS when it
i§
awake.
The interuals
when the Z-Wave RS is awake can
be set using the
WakeUp
Command Class. By
default the Wakeup interval
is 60 minutes
The z-Wave
Rs can be woken manually
by
pushing
any ofthe
three
buttons, and
will stay awake for
10
seconds.
Z-Wave Node
lnformation
Frame
Each time the
LED button is
pressed
the Z-Wave RS
will
and
send NlF.
This is also true
when the Z-Wave RS
i5 in tamper-proofmode.
Factory
Reset
I . Remove
one of the
I
2. Press and hold the
LED button
while
batteries.
J
reinserting the battery
until the
LED
flashes red
(approx.5
seconds).
The Z-
Wave RS
is now reset to
factory defaults,
Eril