Dansons Group Pit Boss Competition PB1000CS

Questions and Answers

A
Amy CollinsAug 19, 2025
What to do if my Dansons Group Grill has no power lights on the control board?
- I
  idavisAug 19, 2025
  First, ensure your grill is properly connected to a working power source and reset the breaker. Confirm that the GFCI is a minimum 15 Amp service. Also, check that all wire connections are firmly connected and dry. If the issue persists, the fuse on the control board might be blown, inspect it and replace if necessary. If all of this is correct, the control board might be faulty and require replacement. Contact Customer Service for a replacement part.
S
Sarah ClarkAug 21, 2025
Why won't my Dansons Group Pit Boss Competition PB1000CS Grill achieve or maintain a stable temperature?
- R
  Ronald PierceAug 22, 2025
  There could be several reasons why your grill isn't maintaining a stable temperature. Check the burn pot for ash build-up or any obstructions, and make sure the fan is working correctly and the air intake isn't blocked. Also, verify the auger motor is operating and there are no blockages in the auger tube. Another cause may be the lack of fuel, poor fuel quality, or an obstruction in the feed system. Check the hopper fuel level and replace any poor-quality pellets. Lastly, check the status of the grill probe; a dirty or damaged probe can affect temperature readings.
N
Nicole Lynch MDAug 25, 2025
What to do if my Dansons Group Pit Boss Competition PB1000CS has a fire in the burn pot that will not light?
- R
  rodriguezdianeAug 25, 2025
  If the fire in the burn pot won't light, it might be because the auger isn't primed, especially if it's the first time using the grill or the hopper was completely empty. In this case, follow the auger priming procedure. Another reason could be a jammed auger motor; inspect the auger feed system to ensure it's dropping pellets into the burn pot. If not, contact Customer Service. Lastly, the igniter might have failed; check if it's working by feeling for heat above the burn pot and ensuring it protrudes about 13mm / 0.5 inches into the burn pot. If it's not working, contact Customer Service.
A
allenkingAug 26, 2025
What does the ErH error code mean on my Dansons Group Grill?
- B
  Brooke CannonAug 26, 2025
  The ErH error code indicates that the unit has overheated, possibly due to a grease fire or excess fuel. To resolve this, press and hold the power button for three seconds to turn the unit off and allow the grill to cool. Follow the care and maintenance instructions. After maintenance, remove the pellets and confirm the positioning of all component parts. Once cooled, press the power button to turn the unit on, then select the desired temperature. If the error code is still displayed, contact Customer Service.
E
Elizabeth BoydAug 28, 2025
What does the Err error code with the PELLET icon blinking mean on my Dansons Group Grill?
- A
  Ariel CalderonAug 28, 2025
  This error code indicates a lack of fuel, poor fuel quality, an obstruction in the feed system, or a jammed auger. Check the hopper to ensure the fuel level is sufficient and replenish if low. If the hardwood pellets are of poor quality or too long, remove them and follow the care and maintenance instructions.
K
Katherine BurgessAug 30, 2025
How to fix frequent flare-ups on my Dansons Group Pit Boss Competition PB1000CS Grill?
- L
  Laurie HartAug 30, 2025
  Frequent flare-ups can occur due to the cooking temperature being too high. Try cooking at a lower temperature, keeping it under 176°C / 350°F when cooking greasy foods. Another cause is grease build-up on cooking components, so follow the care and maintenance instructions.
C
clarkmeganSep 1, 2025
Why is my Dansons Group Pit Boss Competition PB1000CS producing excess or discolored smoke?
- V
  Victoria EnglishSep 1, 2025
  Excess or discolored smoke from your grill can be due to several factors. Grease build-up is a common cause, so follow the care and maintenance instructions. Also, check the hardwood pellet quality; remove any moist pellets and replace them with dry ones. A blocked burn pot or insufficient air intake for the fan can also cause this issue. Clear the burn pot of any moist pellets and ensure the fan is working properly and the air intake isn't blocked.
H
Helen JordanSep 3, 2025
What does the ErL error code mean on my Dansons Group Pit Boss Competition PB1000CS?
- T
  timothyhernandezSep 3, 2025
  The ErL error code means the grill fails to perform the start-up cycle. Check the proper positioning of cooking components. Check the hopper for sufficient fuel or if there is an obstruction in the feed system. Remove pellets and follow the care and maintenance instructions. Check the Grill Probe; confirm if the actual temperature is correct and accurate. Follow the care and maintenance instructions if dirty. Check the igniter positioning and that it is heating up properly. In extreme cold, the grill may require a second start. Turn the grill off, wait, then turn it on again. Check the fan. Ensure it is working properly. Follow the care and maintenance instructions if dirty.
B
bfosterSep 5, 2025
What does the "ErP" error code mean on my Dansons Group Pit Boss Competition PB1000CS?
- B
  benjaminfullerSep 6, 2025
  The "ErP" error code indicates that the grill probe wire is not making a connection. Remove the hopper access panel and check for any damage to the grill probe wires. Ensure the grill probe connectors are firmly connected and connected correctly to the control board.
J
Joseph HuntSep 8, 2025
What does the Err error code with the AUGER icon blinking mean on my Dansons Group Pit Boss Competition PB1000CS?
- M
  Melinda OliverSep 8, 2025
  This error code indicates that the auger is not primed or the auger motor is jammed and not making a connection. If the unit is used for the first time or anytime the hopper is completely emptied out, the auger must be primed to allow pellets to fill the feed system. Remove cooking components from the Main Barrel. Press the Power Button to turn the unit on and inspect the auger feed system. Visually confirm that the auger is dropping pellets into the burn pot. If not operating properly, call Customer Service for assistance or a replacement part.

Dansons Group Pit Boss Competition PB1000CS Specifications

General

Temperature Range	180°F to 500°F
Cooking Grate Material	Porcelain-Coated Steel
Material	Steel
Warranty	5 Years
Grill Category	Pellet
Cooking Area	1000 sq in
Ignition	Electric