Need help?Do you have a question about the dbx DriveRack 260 and is the answer not in the manual?
General| Input Channels | 2 |
|---|---|
| Output Channels | 6 |
| Frequency Response | 20 Hz - 20 kHz, +/-0.5 dB |
| D/A Converter | 24-bit |
| Real Time Analyzer | Yes |
| Input Impedance | >40 kΩ |
| Maximum Input Level | +20 dBu |
| Maximum Output Level | +20 dBu |
| Input Connectors | XLR |
| Output Connectors | XLR |
| Dynamic Range | >110dB |
| A/D Converter | dbx Type IV Conversion System |
| Display | LCD |
| Control Interface | RS-232 |
| EQ | Parametric EQ, Graphic EQ |
| Crossover | Yes |
| Compressor | dbx Compressor |
| Delay | Yes |
| Output Impedance | 120Ω |
| Power Supply | 50/60 Hz |
| Dimensions | 1.75" x 19" |
Details the rear panel connectors for power, PC, zone control, inputs, and outputs.
Describes the front panel controls including LCD, Data Wheel, and function buttons.
Provides a concise guide for initial setup and connecting the DriveRack 260.
Explains core navigation using FX buttons, Next/Prev PG, and Data Wheel.
Details function of each effect button for accessing modules like EQ, Crossover, Dynamics.
Guides on editing Pre-Crossover EQ parameters using GEQ or PEQ modules.
Instructions for editing Crossover parameters, including frequency, slope, and gain.
Explains access to and editing of 'Other' section modules like AFS, Notch Filter.
Details editing parameters for Compressor, Gate, and AGC modules.
Guides on editing Alignment Delay parameters, including time and units.
Describes accessing Utility and Metering functions for system settings and monitoring.
Outlines using System Setup, Auto EQ, and AFS Wizards for configuration.
Explains editing Input and Output levels, pink noise, and phase/polarity settings.
Defines a "program" and the different editing levels within the DriveRack 260.
Explains selecting and loading the 25 factory programs for quick setup.
Details editing parameters within selected modules using Data Wheel and navigation buttons.
Guides on saving edited programs, renaming them, and storing them to user locations.
Explains creating custom configurations by linking/unlinking modules and adjusting signal path.
Explains parameters for Graphic EQ (GEQ) and Parametric EQ (PEQ) before the crossover.
Details the Advanced Feedback Suppression (AFS) module, including operation, modes, and filter settings.
Describes the Subharmonic Synthesizer module for enhancing bass frequencies.
Explains Gate effect parameters: threshold, ratio, attack, hold, release.
Details AGC parameters for maintaining constant signal level: target, gain, thresholds.
Explains Notch Filters for dropping undesirable frequencies: frequency, gain, Q.
Details crossover parameters: frequency, slope types (Bessel, Butterworth, Linkwitz-Riley), and gain.
Describes the 4-band parametric EQ available after the crossover.
Explains Compressor and Limiter parameters, including OverEasy and PeakStop+.
Details Alignment Delay parameters for speaker driver offset and system delay.
Explains input routing mixers (A/B) and mixing input channels for flexible routing.
Details output parameters: level, polarity, and phase shift for output compensation.
Covers LCD contrast adjustment and Auto EQ plot selection (RTA or GEQ).
Explains Power Up Program (Current/Stored) and Power Up Mute (Current/Mute All) options.
Guides on setting up and configuring dbx Zone Controllers (ZC-1 through ZC-4).
Details system lockout and password-protected security features for parameter access.
Explains creating custom program lists and managing program change modes.
Describes accessing metering section to monitor dynamics, zone controllers, and output trims.
Covers system requirements, installation, and configuration of DriveWare PC software.
Explains installation, description, and programming of Zone Controllers.
Setup example for mono 4-way system with two aux zones.
Setup example for stereo tri-amplified system with diagrams and software steps.
Setup example for stereo system with four aux zones, including ZC controller integration.
Details stereo bi-amplified system setup with dual delay, including Zone Controller connections.
Explains how to perform factory or system resets on the DriveRack 260.
Details quick key options for initial power-up: program number change and system lock out.
Lists technical specifications: inputs, outputs, performance metrics.
Provides tips for optimizing Auto EQ: managing room modes and adjusting gain structure.
Illustrates various crossover configurations and signal paths.
Lists factory programs with compatible speaker and power amplifier tunings.
Presents a block diagram of the 260 Signal Path, showing signal flow.
Provides detailed diagrams illustrating input and output signal paths.
Explains changing internal gain level settings using jumpers with warnings.
Guides on maximizing system gain structure and using limiters for amplifier protection.
To Next Page
