EasyManuals Logo

DCS ActiveSmart RS36A72JC User Manual

DCS ActiveSmart RS36A72JC
40 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #25 background imageLoading...
Page #25 background image
23
CLEANING CARE – EXTERIOR
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
RS36A80JC DCS and RS36A80UC DCS
models only
To clean the bottom kickstrip
grille and kickstrip filter:
1
Remove the air flow divider by
pulling towards you (A).
2
To remove the top kickstrip grille,
insert fingers into the left and
right square openings on the
grille. Pull towards you(B).
3
To remove kickstrip filter, insert
fingers into the left and right
square openings on the filter. Pull
towards you. Refer to ‘Removing
and replacing kickstrip filter
drawing.
4
Clean both components with
liquid dishwashing detergent
dissolved in warm water and a
soft lint-free cloth.
5
Rinse with clean water and dry
with a clean, lint-free cloth.
To replace kickstrip filter and
kickstrip grille:
1
To replace kickstrip filter, align
filter tabs onto the rails and push
to the rear until it clips securely.
2
To replace top kickstrip grille,
align securing hooks then firmly
push grille onto product until it
clips securely (C).
3
To replace air flow divider, align
the divider underneath the grille
tabs indicator and clip onto the
vanes of the bottom grille (D).
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
B
Removing top kickstrip grille
4
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
Removing air flow divider
A
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
Replacing top kickstrip grille
C
D
Replacing air flow divider

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the DCS ActiveSmart RS36A72JC and is the answer not in the manual?

DCS ActiveSmart RS36A72JC Specifications

General IconGeneral
BrandDCS
ModelActiveSmart RS36A72JC
CategoryRefrigerator
LanguageEnglish

Related product manuals