DeDietrich C 610 ECO User Manual (English)

Questions and Answers:

A
Andre NguyenAug 23, 2025
What to do if my DeDietrich C 610 ECO shows a BURNER FAILURE?
- C
  Christina MurphyAug 23, 2025
  If the DeDietrich Boiler displays 'BURNER FAILURE', it could be due to several reasons. First, examine the ignition electrode for proper spacing, connector issues, or cable problems; replace it if needed. Second, verify the earth connection and ionisation current; adjust the CO2 level if necessary. Third, a faulty gas valve might be the culprit, requiring replacement. Lastly, ensure there is sufficient gas supply pressure and bleed the gas circuit to remove any air.
K
Kelly CollinsSep 1, 2025
What to do if my DeDietrich C 610 ECO Boiler displays MCBA FAILURE 89?
- C
  Chelsea SmithSep 1, 2025
  If your DeDietrich Boiler displays 'MCBA FAILURE 89' or 'MCBA FAILURE 90', this indicates the detection of a gas leak V1 or V2. Check the gas valve for leaks and replace it if necessary.
T
Tammy RiceAug 31, 2025
What to do if my DeDietrich C 610 ECO displays VALVE FAIL?
- J
  john15Aug 31, 2025
  If your DeDietrich Boiler displays 'VALVE FAIL', it means the combined gas valve unit is faulty. Check the wiring of the gas valve, look for a possible fault in the gas valve (faulty coil), and ensure the fuses are in good working condition.
D
daviskerriAug 29, 2025
What to do if my DeDietrich C 610 ECO Boiler displays STB BALK?
- N
  Nicole LevyAug 30, 2025
  If your DeDietrich Boiler displays 'STB BALK', it means the return temperature is too high. Check the wiring, bleed the boiler, check the boiler pump, and inspect the hydraulic circuit on the installation.
V
vanessa29Aug 28, 2025
What to do if my DeDietrich C 610 ECO Boiler displays FAN ON FAIL?
- S
  saradiazAug 28, 2025
  If your DeDietrich Boiler displays 'FAN ON FAIL', it indicates that the fan is working constantly. This can be due to broken electrical connections or a faulty fan control. Replace the fan and check the electrical connections.
J
josephkristieAug 27, 2025
What to do if my DeDietrich C 610 ECO Boiler displays FAN OFF FAIL?
- D
  Dr. John WatkinsAug 27, 2025
  If your DeDietrich Boiler shows 'FAN OFF FAIL', it means the fan is not working. This could be due to a faulty fan, wiring issues (corrosion), or a faulty command and safety box. Check the fan wiring and replace the fan if necessary. Also, inspect the command and safety box.
L
Laurie EvansAug 27, 2025
What to do if my DeDietrich C 610 ECO displays I-CURRENT FAIL?
- J
  Julie BaldwinAug 27, 2025
  If the DeDietrich Boiler displays 'I-CURRENT FAIL', it indicates an ionisation fault during operation. Check the earth connection and the ionisation current. If necessary, rectify the level of CO2.
E
Eric ReedAug 25, 2025
What to do if my DeDietrich Boiler displays STB EXCHANGE?
- L
  Larry DominguezAug 26, 2025
  If your DeDietrich Boiler shows 'STB EXCHANGE', it indicates that the exchanger temperature is too high. You should check the wiring, bleed the boiler, check the boiler pump, and inspect the hydraulic circuit on the installation.
Z
zloweryAug 25, 2025
What to do if my DeDietrich C 610 ECO displays STB BOILER?
- J
  Jessica CarrollAug 25, 2025
  If your DeDietrich Boiler is showing 'STB BOILER', it means the flow temperature is exceeding the maximum limit. You should check the wiring, bleed the boiler, inspect the boiler pump, and examine the hydraulic circuit on the installation.