What to do if my DeDietrich INNOVENS PRO MCA 160 displays 'Deviation in flow sensor 1 and flow sensor 2 detected'?
If your DeDietrich Boiler shows 'Deviation in flow sensor 1 and flow sensor 2 detected', it indicates a flow temperature sensor deviation. Check the connection for bad connections and replace the sensor if it's faulty.
What to do if my DeDietrich Boiler shows 'Max Tflow'?
If your DeDietrich Boiler displays 'Max Tflow', it means the flow temperature sensor is above the normal range. Check the wiring and connectors for bad connections, ensure the sensor is correctly fitted, and consider replacing the sensor if faulty. Also, check for no flow or insufficient flow by examining the circulation (direction, pump, valves), water pressure, and cleanliness of the heat exchanger.
What to do if my DeDietrich Boiler displays 'Gas Pressure Switch'?
If your DeDietrich Boiler displays 'Gas Pressure Switch', it indicates that the gas pressure is too low. You should check the gas supply pressure, ensure the gas tap is properly open, and inspect the wiring. If these are not the issue, the gas valve may be faulty and need to be checked or replaced.
What to do if my DeDietrich INNOVENS PRO MCA 160 displays 'Max Delta TH-TF'?
If your DeDietrich Boiler is showing 'Max Delta TH-TF', it means the maximum difference between the heat exchanger and flow temperature has been exceeded. Check the circulation (direction, pump, valves) for no flow or insufficient flow. Also, check the water pressure, the cleanliness of the heat exchanger, and ensure the installation has been correctly vented to remove air. Finally, verify the sensors are operating correctly and properly fitted.
What to do if my DeDietrich INNOVENS PRO MCA 160 displays 'Periodically safety check ongoing'?
No action is required. The device restarts itself when the DeDietrich Boiler displays 'Periodically safety check ongoing'.
What to do if my DeDietrich Boiler displays 'Release Signal'?
If your DeDietrich Boiler displays 'Release Signal', it means the waiting time for the release signal has elapsed. You should remove any external causes, check the parameters for wrong settings, and inspect the connection for any issues.
What to do if my DeDietrich INNOVENS PRO MCA 160 displays 'THeat Ex Closed'?
If your DeDietrich Boiler displays 'THeat Ex Closed', it indicates that the heat exchanger temperature sensor is short-circuited. Check the wiring and connectors for bad connections, ensure the sensor is correctly fitted, and replace the sensor if it is faulty.
What to do if my DeDietrich INNOVENS PRO MCA 160 displays 'WaterPressureOpen'?
If your DeDietrich Boiler displays 'WaterPressureOpen', it indicates that the hydraulic pressure sensor is open. Check the wiring and connectors for bad connections, ensure the sensor is correctly fitted, and replace the sensor if it is faulty.
What to do if the fan speed on my DeDietrich Boiler has exceeded normal operating range?
If your DeDietrich Boiler displays 'Fan speed has exceeded normal operating range', it indicates a fan fault. Check the wiring and connectors for bad connections. Also, check for excessive chimney draught if the fan operates when it should not be. If necessary, replace the fan.
What to do if my DeDietrich INNOVENS PRO MCA 160 displays 'False flame detected before burner start'?
If your DeDietrich Boiler displays 'False flame detected before burner start', it indicates a false flame signal. The burner may remain very hot. Check the ionisation/ignition electrode, and if no flame should be present but O 2 Ionisation current is measured. If necessary, replace the faulty gas valve or ignition transformer.
General| Category | Boiler |
|---|---|
| Type | Condensing |
| Model | INNOVENS PRO MCA 160 |
| Power Output | 160 kW |
| Max working pressure | 6 bar |
| Max temperature | 90°C |
| Electrical supply | 230V / 50Hz |
| Protection rating | IPX4D |
| Fuel Type | Natural Gas |
| Efficiency | Up to 109% |
| NOx emissions | Class 6 |
| Connection diameter | DN 50 |
To Next Page
